Author

Shen Qu

Observed names: Qu Shen, S. Qu, Shen QU

Institutions: Chinese Academy of Sciences, Zhejiang Industry Polytechnic College, Institute of Metal Research, Shenyang National Laboratory for Materials Science

Observed institutions: Chinese Academy of Sciences, Dalian University of Technology, Lanzhou Jiaotong University, Zhejiang Industry Polytechnic College, Institute of Metal Research, State Key Laboratory of Structural Analysis for Industrial Equipment, Shenyang National Laboratory for Materials Science, Gansu Open University

ORCID: 0000-0003-4314-5309

Observed ORCID: 0000-0003-4314-5309

OpenAlex ID: A5001845532

Failure modes, mechanisms and causes of shafts in mechanical equipment

2022 · Nan Hou, Ning Ding, et al. · Engineering Failure Analysis · 126

Tensile and compressive properties of AISI 304L stainless steel subjected to equal channel angular pressing

2007 · S. Qu, C.X. Huang, et al. · Materials Science and Engineering A · 122

Influence of stacking-fault energy on the accommodation of severe shear strain in Cu-Al alloys during equal-channel angular pressing

2009 · Xianghai An, Qingyun Lin, et al. · Journal of materials research/Pratt's guide to venture capital sources · 75

Failure analysis of the 1st stage blades in gas turbine engine

2013 · S. Qu, C.M. Fu, et al. · Engineering Failure Analysis · 68

Investigation into diesel engine cylinder head failure

2018 · Guo Xi Jing, Meng Xiao Zhang, et al. · Engineering Failure Analysis · 51

Mechanical properties and failure behavior of hexagonal boron nitride sheets with nano-cracks

2017 · Nan Li, Ning Ding, et al. · Computational Materials Science · 45

Exploring the effect of graphene oxide on freeze–thaw durability of air-entrained mortars

2022 · Hongyan Zeng, Yuanming Lai, et al. · Construction and Building Materials · 44

Microstructure and transport properties of cement-based material enhanced by graphene oxide

2020 · Hongyan Zeng, Shen Qu, et al. · Magazine of Concrete Research · 23

Radial integration boundary element method for acoustic eigenvalue problems

2013 · Shen Qu, Sheng Li, et al. · Engineering Analysis with Boundary Elements · 21

Effect of alloying elements on <111> dislocation in NiAl: A first-principles study

2013 · Bai Lin Lü, Guo Qing Chen, et al. · Physica B Condensed Matter · 14

First-principle calculation of yield stress anomaly of Ni3Al-based alloys

2012 · Bai Lin Lü, Guo Qing Chen, et al. · Materials Science and Engineering A · 14

Failure analysis of the brass tubes in a lubricating oil cooler

2011 · S. Qu, G. Yao, et al. · Engineering Failure Analysis · 13

Knowledge assisted machine learning to clarify pore influence on fatigue life of forging/additive hybrid manufactured Ti-17 alloy

2024 · Shuailong Gao, Wenyuan Li, et al. · Journal of Materials Informatics · 9

Numerical simulation of inertia friction welding process of GH4169 alloy

2004 · Zhang Liwen, Liu Chengdong, et al. · Journal de Physique IV (Proceedings) · 9

Microstructure Evolution and Mechanical Properties of Fcc Metallic Materials Subjected to Equal Channel Angular Pressing

2010 · Shiding WU, Xianghai AN, et al. · Acta Metallurgica Sinica · 8

Adaptive Integration Method Based on Sub-Division Technique for Nearly Singular Integrals in Near-Field Acoustics Boundary Element Analysis

2014 · Shen Qu, Haoran Chen, et al. · Journal of low frequency noise, vibration and active control · 6

Failure Analysis of Over-Temperature of Aero-Engine Bearing

2023 · Yunfei Zhong, Tianfu Li, et al. · Journal of Failure Analysis and Prevention · 5

Stress Corrosion Cracking of an Electrohydraulic Oil Pipe

2019 · Nan Li, Ning Ding, et al. · Journal of Failure Analysis and Prevention · 3

Corrosion Failure of 304 Stainless Steel Hooks in a Brick Kiln

2018 · Long Liu, Ning Ding, et al. · Journal of Failure Analysis and Prevention · 2

Failure Analysis of a Diesel Engine Crankshaft

2021 · H. Y. Zhang, S. Qu, et al. · Practical Metallography · 1

Numerical simulation of weld tab length influence on welding residual stress and distortion of aero-engine disk

2009 · Xue-qiu Zhang, Jian-guo Yang, et al. · Frontiers of Materials Science in China · 1

Discussion and calculation on welding residual longitudinal stress and plastic strain by finite element method

2008 · Hong-yuan Fang, Xue-qiu Zhang, et al. · Frontiers of Materials Science in China · 1

Improving the Durability and Interfacial Reinforcement of Basalt Fibers by Coating with Graphene Oxide to Improve the Stability of Concrete in Frozen Soil with Saline

2026 · Hongyan Zeng, Yuhui Wang, et al. · ACS Applied Nano Materials

High-cycle Fatigue Failure Mechanism of Wire Arc Additive Manufacturing (WAAM) Repaired Ti-5Al-2Sn-2Zr-4Cr-4Mo Alloy

2026 · Yuan-Hui Duan, Yun-Hai Su, et al. · Journal of Failure Analysis and Prevention

Cause analysis of the cracking at the gas outlet edge of a gas turbine combustor

2024 · H. Zhang, G. Zhang, et al. · Practical Metallography

Works count: 30

Citation count: 665

H-index: 12

I10-index: 12