Get started
Author

Серебренникова Анжела Геннадьевна

Observed names: A G Serebrennikova, A. G. Serebrennikova, A. Serebrennikova, A.G. Serebrennikova, Anzhela G. Serebrennikova, Anzhela Serebrennikova, Анжела Серебренникова
ORCID: 0000-0001-9144-7489
Observed ORCID: 0000-0001-9144-7489
OpenAlex ID: A5004369647
Research Results Of Stress-Strain State Of Cutting Tool When Aviation Materials Turning
2018 · A G Serebrennikova, E P Nikolaeva, et al. · Journal of Physics Conference Series · 14
PDF
Selection and Analysis of Parameters for Composite Carbide End Mills
2014 · Boris Y. Mokritskii, Dmitriy A. Pustovalov, et al. · Applied Mechanics and Materials · 5
High Speed Milling Difficult Materials: 2. Features of the Workability at Milling
2013 · Yuri Gagarin Aviation Plant, JSC ", Sergey V. Breev, et al. · Scholarly Notes of Komsomolsk-na-Amure State Technical University · 4
An Experimental Study of Chip Shrinkage in Turning Wrought Aluminum Alloys
2022 · A. Serebrennikova, S. Timofeev · Lecture notes in mechanical engineering · 3
A Study of Effects of the Cutting Tool Geometry on the Output Parameters When Turning VT22 Titanium Alloy
2022 · A. G. Serebrennikova, A. V. Savilov · Lecture notes in mechanical engineering · 3
VT22 titanium alloy: study of the cutting tool geometry effect on output parameters of turning process
2020 · Anzhela Serebrennikova, Vladimir Gurylyov · iPolytech Journal · 2
Results of Comparative Study of Cutting Tool Performance When Machining Specialized Stainless Steels
2018 · Boris Mokritskiy, Anzhela Serebrennikova · iPolytech Journal · 2
Studies on the Effect of Output Parameters on Productivity When Turning Titanium Alloys
2021 · A. V. Savilov, A. G. Serebrennikova · Lecture notes in mechanical engineering · 1
High Productivity Turning of Stainless Steel 06Cr14H6Cu2MoNbTi
2021 · Anzhela G. Serebrennikova, Andrey V. Savilov, et al. · Lecture notes in networks and systems · 1
High Speed Milling of Problem Materials: 1. Key Features and Properties of Milling Operation
2013 · Sergey V. Breev, Anzhela G. Serebrennikova · Scholarly Notes of Komsomolsk-na-Amure State Technical University · 1
Diagnostics of the Milling Process With a Composite Milling Cutter With a Progressive Cutting Scheme Based on the Wear Values of the Cutting Plates in Different Milling Conditions
2025 · B. Ya. Mokritsky, A. V. Kosmynin, et al. · Kontrol Diagnostika
Milling of Superhard Materials at an Ensured Rational State of the Technological Cutting System. Part 1
2024 · B. Ya. Mokritskii, A. V. Kosminin, et al. · Russian Metallurgy (Metally)
Milling of Superhard Materials at an Ensured Rational State of the Technological Cutting System. Part 2
2024 · B. Ya. Mokritskii, A. V. Kosminin, et al. · Russian Metallurgy (Metally)
Assurance of surface quality and productivity of machining at milling titanium alloys VT20 and VT22
2020 · Anzhela Serebrennikova, Andrey Savilov · Science intensive technologies in mechanical engineering
PDF
Повышение работоспособности твёрдосплавного режущего инструмента за счет нанесения покрытий
2019 · Мокрицкий Борис Яковлевич, Ситамов Эрадж Сикандарович, et al. · iPolytech Journal
Результаты Сравнительного Исследования Работоспособности Режущих Инструментов При Обработке Специализированных Нержавеющих Сталей
2018 · Мокрицкий Борис Яковлевич, Серебренникова Анжела Геннадьевна · iPolytech Journal
Firmware Realization for Optimum Cutting Speed Definition at Hard-to-machine Material Working
2016 · Мария Козлова, Mariya Kozlova, et al. · Bulletin of Bryansk state technical university
PDF
Championship Worldskills: Theoretical Knowledge and Skills
2016 · A. G. Serebrennikova, E. V. Asafyeva, et al. · Scholarly Notes of Komsomolsk-na-Amure State Technical University
PDF
Modeling the Dynamics of Cutting in High Machining
2011 · Sergey V. Bilenko, Vassily I. Muravyev, et al. · Scholarly Notes of Komsomolsk-na-Amure State Technical University
Works count: 20
Citation count: 36
H-index: 3
I10-index: 1
Year
Topic
Type