Get started
Author

P. Sam Paul

Observed names: P Sam Paul, P. S. Paul, P.Sam Paul, Sam Paul
Institution: Karunya University
ORCID: 0000-0003-3450-3127
Observed ORCID: 0000-0003-3450-3127
OpenAlex ID: A5005203478
A review of challenges and solutions in the preparation and use of magnetorheological fluids
2019 · James Sathya Kumar, P. Sam Paul, et al. · International Journal of Mechanical and Materials Engineering · 240
A multi-sensor fusion model based on artificial neural network to predict tool wear during hard turning
2012 · P Sam Paul, AS Varadarajan · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · 69
A neural network model to predict surface roughness during turning of hardened SS410 steel
2020 · X. Ajay Vasanth, P. Sam Paul, et al. · International Journal of Systems Assurance Engineering and Management · 44
Study on the influence of fluid application parameters on tool vibration and cutting performance during turning of hardened steel
2015 · P. Sam Paul, A.S. Varadarajan, et al. · Engineering Science and Technology an International Journal · 44
PDF
Attenuation of vibration in boring tool using spring controlled impact damper
2015 · G. Lawrance, P. Sam Paul, et al. · International Journal on Interactive Design and Manufacturing (IJIDeM) · 41
Effect of magnetic field on damping ability of magnetorheological damper during hard turning
2013 · P. Sam Paul, A.S. Varadarajan, et al. · Archives of Civil and Mechanical Engineering · 39
Vibration control techniques during turning process: a review
2019 · X. Ajay Vasanth, P. Sam Paul, et al. · Australian Journal of Mechanical Engineering · 37
Performance evaluation of hard turning of AISI 4340 steel with minimal fluid application in the presence of semi-solid lubricants
2013 · P Sam Paul, AS Varadarajan · Proceedings of the Institution of Mechanical Engineers Part J Journal of Engineering Tribology · 33
Effect of magnetorheological fluid on tool wear during hard turning with minimal fluid application
2014 · P. Sam Paul, A.S. Varadarajan, et al. · Archives of Civil and Mechanical Engineering · 30
Effectiveness of particle and mass impact damping on tool vibration during hard turning process
2016 · P Sam Paul, Prashanth Raja, et al. · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · 27
Influence of magnetorheological elastomer on tool vibration and cutting performance during boring of hardened AISI4340 steel
2019 · G. Lawrance, P. Sam Paul, et al. · Journal of Mechanical Science and Technology · 24
Application of smart fluid to control vibration in metal cutting: a review
2021 · S. Sarath, P. Sam Paul · World Journal of Engineering · 20
Suppression of Tool Vibration in Boring Process: A Review
2019 · G. Lawrance, P. Sam Paul, et al. · Journal of The Institution of Engineers (India) Series C · 20
Effect of Bearings on Vibration in Rotating Machinery
2017 · Rudrapati Victor Daniel, Savale Amit Siddhappa, et al. · IOP Conference Series Materials Science and Engineering · 20
PDF
Effect of magneto rheological damper on tool vibration during hard turning
2012 · P. Sam Paul, A. S. Varadarajan · Frontiers of Mechanical Engineering · 19
Effect of nanoparticles on the performance of magnetorheological fluid damper during hard turning process
2015 · P. Sam Paul, J. Agnelo Iasanth, et al. · Friction · 16
PDF
A Novel Architecture for 10-bit 40MSPS Low Power Pipelined ADC Using a Simultaneous Capacitor and Op-amp Sharing Technique
2021 · D.S.Shylu Sam, D. Jackuline Moni, et al. · Silicon · 11
PDF
Design of a power-efficient Kogge–Stone adder by exploring new OR gate in 45nm CMOS process
2020 · Vimukth John, Shylu Sam, et al. · Circuit World · 11
Effect of metallic substrate and rubber elastic materials over passive constrained layer damping on tool vibration during boring process
2024 · G Lawrance, P Sam Paul, et al. · Journal of low frequency noise, vibration and active control · 10
A 10-bit 200 MS/s pipelined ADC with parallel sampling and switched op-amp sharing technique
2021 · D.S. Shylu Sam, P. Sam Paul · Circuit World · 9
Study on the influence of magnetorheological fluid on tool vibration during end milling process
2015 · P. Sam Paul, C. K. Shobhan Kumar, et al. · International Journal of Dynamics and Control · 9
Analysis of Dynamic Characteristics of Boring Tool Holder
2014 · P. Sam Paul, G. Lawrence, et al. · Procedia Materials Science · 9
PDF
A Novel architecture of a Low Power Folded Cascode OTA in 180nm CMOS process
2021 · D. S. Shylu Sam, P. Sam Paul, et al. · International Conference on Advanced Computing and Communication Systems (ICACCS) · 8
Study On The Influence Of Shaft Material On Vibration In Rotating Machinery
2018 · Gerald Chandrashekar, Winston Raj, et al. · Materials Today Proceedings · 8
Effect of material on damping characteristics of impact mass during hard turning
2015 · P. S. Paul, A. S. Varadarajan, et al. · Emerging Materials Research · 8
Works count: 72
Citation count: 918
H-index: 16
I10-index: 19
Year
Topic
Type