Get started
Author

Muhammet Uludağ

Observed names: M. Uludağ, Muhammet ULUDAĞ, Muhammet UludaĞ, ULUDAĞ, Muhammet, Uludağ, Muhammet
Observed institutions: Selçuk University, Bursa Technical University, Haliç University, Necmettin Erbakan University, Pamukkale University, Istanbul Technical University
ORCID: 0000-0001-9150-3292
Observed ORCID: 0000-0001-9150-3292
OpenAlex ID: A5006403048
Experimental and statistical analysis of low velocity impact response of filament wound composite pipes
2018 · Lokman Gemi, Mehmet Kayrıcı, et al. · Composites Part B Engineering · 122
Evaluation of the Effects of Rotary Degassing Process Variables on the Quality of A357 Aluminum Alloy Castings
2016 · M. Mostafaei, M. Ghobadi, et al. · Metallurgical and Materials Transactions B · 45
On the Interpretation of Melt Quality Assessment of A356 Aluminum Alloy by the Reduced Pressure Test: The Bifilm Index and Its Physical Meaning
2018 · Muhammet Uludağ, Remzi Çetin, et al. · International Journal of Metalcasting · 44
Characterization of the Effect of Melt Treatments on Melt Quality in Al-7wt %Si-Mg Alloys
2017 · Muhammet Uludağ, Remzi Çetin, et al. · Metals · 41
PDF
The effects of degassing, grain refinement & Sr-addition on melt quality-hot tear sensitivity relationships in cast A380 aluminum alloy
2018 · Muhammet Uludağ, Remzi Çetin, et al. · Engineering Failure Analysis · 38
Freezing Range, Melt Quality, and Hot Tearing in Al-Si Alloys
2018 · Muhammet Uludağ, Remzi Çetin, et al. · Metallurgical and Materials Transactions A · 37
Relationship Between Machinability, Microstructure, and Mechanical Properties of Al-7Si Alloy
2018 · Muhammet Uludağ, Şakir Yazman, et al. · Journal of Testing and Evaluation · 26
Change in Porosity of A356 by Holding Time and Its Effect on Mechanical Properties
2018 · Muhammet Uludağ, Remzi Çetin, et al. · Journal of Materials Engineering and Performance · 20
Effect of Degassing and Grain Refinement on Hot Tearing Tendency in Al8Si3Cu Alloy
2017 · Muhammet Uludağ, Remzi Çetin, et al. · International Journal of Metalcasting · 18
Correlation Between Machinability and Chip Morphology of Austempered Ductile Iron
2017 · Ş. Yazman, L. Gemı, et al. · Journal of Testing and Evaluation · 13
Assessment of Mechanism of Pore Formation in Directionally Solidified A356 Alloy
2017 · M. Uludağ, D. Dişpinar · Archives of Foundry Engineering · 13
The Effect of Bifilm and Sr Modification on the Mechanical Properties of AlSi12Fe Alloy
2020 · M. Uludağ, M. Gurtaran, et al. · Archives of Foundry Engineering · 12
PDF
Influence of Al-B grain refiner on porosity formation of directionally solidified Al-Si alloys
2020 · Muhammet Uludağ · China Foundry · 11
Effect of Sr and Ti Addition on the Corrosion Behaviour of Al-7Si-0.3Mg Alloy
2017 · M. Uludağ, M. Kocabaş, et al. · Archives of Foundry Engineering · 11
PDF
Effect of Ti addition holding time on casting quality and mechanical properties of A356 alloy
2020 · Mikdat Gurtaran, Muhammet Uludağ · SN Applied Sciences · 8
PDF
A Statistical Assessment of Casting Quality–Tribological Properties of Eutectic Al-12Si Alloy: Effect of Mg
2020 · Muhammet Uludağ · Journal of Materials Engineering and Performance · 6
Study on mechanical and microstructural properties of advanced high-strength welded sheet metal
2023 · Pruva Automotive, Bursa, Turkey, Serkan Damlacik, et al. · Tribology and Materials · 5
PDF
Experimental and Statistical Analysis of Effect of Si Modification and Grain Refinement on Tensile Properties of A356 Alloy
2020 · Muhammet ULUDAĞ · Journal of Polytechnic · 5
PDF
The Effect of Sr Modification and Holding Time on Si Morphology and Mechanical Properties of ETIAL 195 Alloy
2015 · Muhammet Uludağ, Lokman Gemi, et al. · Pamukkale University Journal of Engineering Sciences · 5
PDF
Observation of Hot Tearing in Sr-B Modified A356 Alloy
2017 · M. Uludağ, R. Çetin, et al. · Archives of Foundry Engineering · 4
PDF
The Effect of Holding Time and Solidification Rate on Porosity of A356
2016 · Muhammet Uludağ, Lokman Gemi, et al. · 4
Production of Al7075 Alloy via Recycling of Al6063 and Zamak 5 Scraps: Chemical Composition Control and Liquid Metal Quality Assessment
2026 · Özkan Kaya, Furkan Demir, et al. · International Journal of Metalcasting · 3
PDF
The Effect of Si Morphology on Machinability of Al-Si Alloys
2015 · Muhammet Uludağ, Şakir Yazman, et al. · Pamukkale University Journal of Engineering Sciences · 3
PDF
ETİAL 221 Alaşımında Katılaşma Hızı ve Su Verme Ortamlarının Mekanik Özelliklere Etkisinin İstatistiksel Analizi
2020 · Muhammet ULUDAĞ, Lokman GEMİ, et al. · Uludağ University Journal of The Faculty of Engineering · 2
PDF
Investigation of the Relationship Between Casting Quality, Microstructure and Mechanical Properties in Al-18Si Alloy
2018 · Muhammet ULUDAĞ · Uluslararası mühendislik araştırma ve geliştirme dergisi · 2
PDF
Works count: 49
Citation count: 506
H-index: 12
I10-index: 14
Year
Topic
Type