Get started
Author

Abou Bakr Elshalakany

Observed names: A. B. Elshalakny, Abou Bakr El Shalakany, Abou Bakr ElshalakanyÂ, Abou Bakr Elshalakny
ORCID: 0000-0003-4863-2296
Observed ORCID: 0000-0003-4863-2296
OpenAlex ID: A5009291261
Microstructure and Mechanical Properties of MWCNTs Reinforced A356 Aluminum Alloys Cast Nanocomposites Fabricated by Using a Combination of Rheocasting and Squeeze Casting Techniques
2014 · Abou Bakr Elshalakany, T. A. Osman, et al. · Journal of Nanomaterials · 95
Influence of friction stir welding parameters on metallurgical and mechanical properties of dissimilar AA5454–AA7075 aluminum alloys
2019 · Mohamed M. Abd Elnabi, Abou Bakr Elshalakany, et al. · Journal of Materials Research and Technology · 88
PDF
Influence of β-phase stability in elemental blended Ti-Mo and Ti-Mo-Zr alloys
2020 · Prakash Mohan, Dipen Kumar Rajak, et al. · Micron · 54
PDF
Experimental design of Al 2 O 3 /MWCNT/HDPE hybrid nanocomposites for hip joint replacement
2020 · Sameh Dabees, Bahaa M. Kamel, et al. · Bioengineered · 51
PDF
Tribological Performance and Rheological Properties of Engine Oil with Graphene Nano-Additives
2022 · Bader Alqahtani, Wael Hoziefa, et al. · Lubricants · 48
PDF
The effect of MWCNTs/GNs hybrid addition on the tribological and rheological properties of lubricating engine oil
2020 · Bahaa M. Kamel, Emad El-Kashif, et al. · Journal of Dispersion Science and Technology · 44
Evaluation of the formation of intermetallic compounds at the intermixing lines and in the nugget of dissimilar steel/aluminum friction stir welds
2020 · Mohamed M. Abd Elnabi, T.A. Osman, et al. · Journal of Materials Research and Technology · 42
PDF
Comparative study between high-velocity oxygen fuel and flame spraying using MCrAlY coats on a 304 stainless steel substrate
2019 · Abou Bakr Elshalakany, T.A. Osman, et al. · Journal of Materials Research and Technology · 40
Investigating the influence of 3D printing parameters on the mechanical characteristics of FDM fabricated (PLA/Cu) composite material
2024 · Mohamed Hamoud, Abou Bakr Elshalakany, et al. · The International Journal of Advanced Manufacturing Technology · 37
PDF
Synthesis and characterization studies of high-density polyethylene -based nanocomposites with enhanced surface energy, tribological, and electrical properties
2021 · Sameh Dabees, Abou Bakr Elshalakany, et al. · Polymer Testing · 30
PDF
Improved mechanical and tribological properties of A356 reinforced by MWCNTs
2018 · Abou Bakr El Shalakany, Bahaa M. Kamel, et al. · Fullerenes Nanotubes and Carbon Nanostructures · 28
Effect of Fe content, sintering temperature and powder processing on the microstructure, fracture and mechanical behaviours of Ti-Mo-Zr-Fe alloys
2017 · P. Mohan, Abou Bakr Elshalakany, et al. · Journal of Alloys and Compounds · 27
PDF
Novel Tribological Behavior of Hybrid MWCNTs/MLNGPs as an Additive on Lithium Grease
2016 · M. E. Ashour, T. A. Osman, et al. · Journal of Tribology · 26
Characterization and mechanical properties of stir-rheo-squeeze cast AA5083/MWCNTs/GNs hybrid nanocomposites developed using a novel preform-billet method
2020 · Abou Bakr Elshalakany, Vineet Tirth, et al. · Journal of Materials Research and Technology · 24
PDF
Microstructure and Mechanical Properties of Ti-Mo-Zr-Cr Biomedical Alloys by Powder Metallurgy
2017 · Abou Bakr Elshalakany, Shady Ali, et al. · Journal of Materials Engineering and Performance · 19
PDF
Rheological behavior of lithium grease with CNTs/GNPs hybrid nanocomposite as an additive
2018 · Mohamed Ashour, Alaa Mohamed, et al. · Industrial Lubrication and Tribology · 18
Investigation of gear performance of MLNGPs as an additive on polyamide 6 spur gear
2018 · Esraa M. Afifi, Abou Bakr Elshalakny, et al. · Fullerenes Nanotubes and Carbon Nanostructures · 17
Investigation of Dynamic-Mechanical-Thermal Analysis of Innovative Hybrid Carbon/Glass Fibers Reinforced by GNPs and Al2O3 for Marine Structures
2023 · Mohamed Abu-Okail, Metwally Abdel Ghafaar, et al. · Fibers and Polymers · 16
PDF
Effect of dispersion hybrid structural properties of MWCNTs and Al2O3 on microstructural and thermal characteristics of PCMs for thermal energy storage in solar water desalination
2023 · Omar T. Bafakeeh, Mohamed S. Shiba, et al. · Journal of Thermal Analysis and Calorimetry · 16
Modeling and Optimization of Friction Stir Welding Parameters for Joining Dissimilar Aluminum Alloys
2018 · Mohamed Mohamed Abd Elnabi, Tarek Abd Elsadek Osman, et al. · Advanced Journal of Graduate Research · 14
PDF
Mechanical properties of titanium alloys additive manufacturing for biomedical applications
2023 · Abou Bakr Elshalakany, M.M. Abdel-Mottaleb, et al. · Elsevier eBooks · 11
Review—A Conceptual Analysis on Ceramic Materials Used for Dental Practices: Manufacturing Techniques and Microstructure
2022 · Sumanth Ratna Kandavalli, Sunanda Ratna Kandavalli, et al. · ECS Journal of Solid State Science and Technology · 11
PDF
Mechanical Properties and Microstructure of Dissimilar Friction Stir Welding of Pure Aluminum to Low Carbon Steel
2018 · Mohamed Mohamed Abd Elnabi, Tarek Abd Elsadek Osman, et al. · Advanced Journal of Graduate Research · 11
PDF
An experimental investigation of the formability of low carbon steel tailor-welded blanks of different thickness ratios
2016 · Abou Bakr Elshalakany, Shady Ali, et al. · The International Journal of Advanced Manufacturing Technology · 11
Comparison of 3D Printed Underwater Propeller Using Polymers and Conventionally Developed AA6061
2022 · H. M. T. Khaleed, Irfan Anjum Badruddin, et al. · Journal of Materials Engineering and Performance · 7
Works count: 33
Citation count: 802
H-index: 17
I10-index: 24
Year
Topic
Type