Get started
Author

Tomasz Paczkowski

Observed names: Paczkowski Tomasz, Paczkowski, Tomasz, T. Paczkowski
ORCID: 0000-0003-2861-8817
Observed ORCID: 0000-0003-2861-8817
OpenAlex ID: A5011607122
Generative AI in AI-Based Digital Twins for Fault Diagnosis for Predictive Maintenance in Industry 4.0/5.0
2025 · Emilia Mikołajewska, Dariusz Mikołajewski, et al. · Applied Sciences · 164
Recent Advances in Bipedal Walking Robots: Review of Gait, Drive, Sensors and Control Systems
2022 · Tadeusz Mikolajczyk, Emilia Mikołajewska, et al. · Sensors · 135
PDF
Energy Sources of Mobile Robot Power Systems: A Systematic Review and Comparison of Efficiency
2023 · Tadeusz Mikołajczyk, Dariusz Mikołajewski, et al. · Applied Sciences · 107
PDF
CAD CAM System for Manufacturing Innovative Hybrid Design Using 3D Printing
2019 · Tadeusz Mikolajczyk, Tomasz Malinowski, et al. · Procedia Manufacturing · 58
PDF
Computer simulation of two-dimensional electrolyte flow in electrochemical machining
2005 · L. Dabrowski, T. Paczkowski · Russian Journal of Electrochemistry · 48
Influence of the main cutting edge angle value on minimum uncut chip thickness during turning of C45 steel
2020 · Tadeusz Mikołajczyk, Hubert Latos, et al. · Journal of Manufacturing Processes · 40
Monitoring and control of the electrochemical machining process under the conditions of a vibrating tool electrode
2017 · Tomasz Paczkowski, Jarosław Zdrojewski · Journal of Materials Processing Technology · 40
Electrochemical Machining of Curvilinear Surfaces
2008 · Tomasz Paczkowski, Jerzy Sawicki · Machining Science and Technology · 33
A Breakthrough in Producing Personalized Solutions for Rehabilitation and Physiotherapy Thanks to the Introduction of AI to Additive Manufacturing
2025 · Emilia Mikołajewska, Dariusz Mikołajewski, et al. · Applied Sciences · 29
PDF
Electrochemical Machining of Curvilinear Surfaces of Revolution: Analysis, Modelling, and Process Control
2022 · Jerzy Sawicki, Tomasz Paczkowski · Materials · 21
PDF
Using CAD CAM system for manufacturing of innovative cutting tool
2018 · Tadeusz Mikolajczyk, Hubert Latos, et al. · Procedia Manufacturing · 19
PDF
Research on Using an Unconventional Tool for Increasing Tool Life by Selective Exchange of Worn Cutting Edge
2022 · Tadeusz Mikolajczyk, Tomasz Paczkowski, et al. · Applied Sciences · 16
PDF
Theoretical and experimental research of edge inclination angle effect on minimum uncut chip thickness in oblique cutting of C45 steel
2022 · Tadeusz Mikołajczyk, Hubert Latos, et al. · The International Journal of Advanced Manufacturing Technology · 14
PDF
Innovative tools for oblique cutting
2018 · Tadeusz Mikolajczyk, Hubert Latos, et al. · Procedia Manufacturing · 14
PDF
Effect of the hydrodynamic conditions of electrolyte flow on critical states in electrochemical machining
2015 · Jerzy Sawicki, Tomasz Paczkowski · EPJ Web of Conferences · 12
PDF
The Mechanism of ECM Technology Design for Curvilinear Surfaces
2016 · Tomasz Paczkowski, Jaroslaw Zdrojewski · Procedia CIRP · 9
PDF
Electrode tool designing in the ECM machining for curvilinear surfaces
2010 · Tomasz Paczkowski, J. Zdrojewski · Journal of Machine Engineering · 9
The Effect of Multidirectional Vibration On Electrochemical Machining
2018 · Tomasz Paczkowski, Adam Troszyński · Procedia Manufacturing · 8
PDF
Composite material delamination during drilling
2016 · Tadeusz Leppert, Tomasz Paczkowski, et al. · Mechanik · 6
PDF
Boundary conditions analysis of ECM machining for curvilinear sufraces
2011 · Tomasz Paczkowski, J. Zdrojewski · Journal of Polish CIMAC/Journal of Polish CIMEEAC · 6
Modelowanie obróbki ECM powierzchni o zarysie krzywoliniowym
2007 · Tomasz Paczkowski · Inżynieria Maszyn · 5
The influence of the structural steel grade and galvanizing time on the thickness and surface condition of the applied coatings
2025 · Natalia Kiełpińska, Mateusz Rojewski, et al. · Advances in Science and Technology – Research Journal · 4
PDF
Analysis of the Deviation in a Low-Cost System for Stepless Digital Control of Conventional Lathe Spindle Speeds
2018 · Tadeusz Mikolajczyk, Tomasz Paczkowski, et al. · Applied Sciences · 3
PDF
Obróbka elektrochemiczna krzywoliniowych powierzchni obrotowych
2004 · J. Sawicki, Tomasz Paczkowski · Zeszyty Naukowe. Mechanika / Akademia Techniczno-Rolnicza w Bydgoszczy · 3
Symulacja komputerowa procesu ECM w oparciu o dwuwymiarowy model przepływu elektrolitu między płaskimi elektrodami
2002 · Tomasz Paczkowski, J. Sawicki · Zeszyty Naukowe. Mechanika / Akademia Techniczno-Rolnicza w Bydgoszczy · 3
Works count: 52
Citation count: 817
H-index: 14
I10-index: 15
Year
Topic
Type