Get started
Author

Sinan Kesriklioglu

Observed names: Kesriklioğlu, Sinan, Sinan KESRİKLİOĞLU, Sinan Kesriklioğlu
ORCID: 0000-0002-2914-808X
Observed ORCID: 0000-0002-2914-808X
OpenAlex ID: A5012580701
Real time temperature measurement with embedded thin-film thermocouples in milling
2018 · Sinan Kesriklioglu, Frank E. Pfefferkorn · Procedia CIRP · 28
PDF
Tool–Chip Interface Temperature Measurement in Interrupted and Continuous Oblique Cutting
2017 · Sinan Kesriklioglu, Justin D. Morrow, et al. · Journal of Manufacturing Science and Engineering · 22
Characterization of Tool–Chip Interface Temperature Measurement With Thermocouple Fabricated Directly on the Rake Face
2019 · Sinan Kesriklioglu, Cory Arthur, et al. · Journal of Manufacturing Science and Engineering · 18
Ineffectiveness of flood cooling in reducing cutting temperatures during continuous machining
2022 · Sinan Kesriklioglu · The International Journal of Advanced Manufacturing Technology · 11
Experimental and statistical damage analysis in milling of S2 ‐glass fiber/epoxy and basalt fiber/epoxy composites
2024 · Ahmed Cagri Sayin, Sengul Danisman, et al. · Polymer Composites · 10
Prediction of Tool-Chip Interface Temperature in Cryogenic Machining of Ti–6Al–4V: Analytical Modeling and Sensitivity Analysis
2018 · Sinan Kesriklioglu, Frank E. Pfefferkorn · Journal of Thermal Science and Engineering Applications · 8
Tool-Chip Interface Temperature Measurement in Interrupted and Continuous Oblique Cutting
2017 · Sinan Kesriklioglu, Justin D. Morrow, et al. · ASME International Manufacturing Science and Engineering Conference (MSEC) · 8
Comparison of Ensemble and Base Learner Algorithms for the Prediction of Machining Induced Residual Stresses in Turning of Aerospace Materials
2022 · Selim BUYRUKOĞLU, Sinan KESRİKLİOĞLU · Bitlis Eren Üniversitesi Fen Bilimleri Dergisi · 4
PDF
Surface integrity and tool wear in s2-GFRP milling: experimental and statistical evaluation of cutting parameters and DLC and TiAlN tool coatings
2026 · Şengül Danışman, Emin Ersoy, et al. · The International Journal of Advanced Manufacturing Technology · 1
Experimental Comparative Analysis of Hole‐Making Strategies and Cutting Parameters on Flexural Properties and Induced Delamination in S 2 Glass and Basalt Fiber‐Reinforced Polymers
2026 · Sara Saeed Abdulrahman Eltahir, Cagatay Yilmaz, et al. · Polymer Composites · 1
Optimization of turning parameters to minimize surface roughness and tool wear in carbon fiber and glass fiber composite rods
2025 · Kemal Cengiz, Sinan Kesriklioğlu · International Advanced Researches and Engineering Journal · 1
PDF
Accurate Prediction of Residual Stresses in Machining of Inconel 718 Alloy through Crystal Plasticity Modelling
2023 · Sinan KESRİKLİOĞLU, Mehmet Fazıl KAPÇI, et al. · Afyon Kocatepe University Journal of Sciences and Engineering · 1
PDF
Correction: Surface integrity and tool wear in s2-GFRP milling: experimental and statistical evaluation of cutting parameters and DLC and TiAlN tool coatings
2026 · Şengül Danışman, Emin Ersoy, et al. · The International Journal of Advanced Manufacturing Technology
PDF
Investigation of milling-induced effects on the fatigue life of S2-glass composite structures through experimental study and statistical optimization of machining conditions
2026 · Sara Saeed Abdulrahman Eltahir, Melih Seçkin, et al. · Materials Research Express
PDF
Author response for "Investigation of Milling-Induced Effects on the Fatigue Life of S2-Glass Composite Structures through Experimental Study and Statistical Optimization of Machining Conditions"
2026 · Sara Saeed Abdulrahman Eltahir, Melih Seçkin, et al. · Publons reviews and discussion
Minimization of thermal stresses in instrumented cutting tools with embedded thin film thermocouples
2026 · Abdurrahman Sivesoglu, Sinan Kesriklioglu · Journal of Mechanical Science and Technology
Sustainable Approach to Fabricating Flat Micro Ribbon Electric Wires Directly from Turning Process Chips
2026 · Abdurrahman Sivesoglu, Sinan Kesriklioglu · Procedia CIRP
Mechanical Properties of Titanium Oxide Thin Films Deposited by Magnetic Field Sputtering at Different Parameters
2024 · Sayın, Ahmed Çağrı, Ersoy, Emin, et al. · Erciyes University - AVESIS
EFFECT OF TiN COATED AND UNCOATED CARBIDE END MILLS ON THE MACHINING OF ST52 STEEL
2024 · Danışman, Şengül, Şahin, Mehmet, et al. · Erciyes University - AVESIS
A parametric study for drilling high quality holes on glass fiber composites
2022 · Sinan KESRİKLİOĞLU · Journal of Advances in Manufacturing Engineering
Works count: 20
Citation count: 113
H-index: 7
I10-index: 5
Year
Topic
Type