Get started
Author

Jonny Singla

ORCID: 0000-0001-7579-7016
Observed ORCID: 0000-0001-7579-7016
OpenAlex ID: A5019560988
Influence of post heat treatment on metallurgical, mechanical, and corrosion analysis of wire arc additive manufactured inconel 625
2023 · Himanshu Sharma, Jonny Singla, et al. · Journal of Materials Research and Technology · 66
Dry sliding and slurry abrasion behaviour of wire arc additive manufacturing – Cold metal transfer (WAAM-CMT) cladded inconel 625 on EN8 steel
2022 · Hrishav Raushan, Anuj Bansal, et al. · Tribology International · 60
Influence of cryogenic treatment on mechanical performance of friction stir Al-Zn-Cu alloy weldments
2020 · Anuj Bansal, Anil Kumar Singla, et al. · Journal of Manufacturing Processes · 56
Microstructural and mechanical properties of Al-5356 alloy structures fabricated using direct energy deposition (DED): In-pursuit to optimizing deposition parameters
2024 · Jonny Singla, Navin Kumar, et al. · Materials Characterization · 25
Development, characterization, and cavitation erosion analysis of high velocity oxy-fuel (HVOF) sprayed TiC and (70Cu-30Ni)-Cr based composite coatings on SS316 steel
2023 · Rampal, Anil Kumar Singla, et al. · Tribology International · 24
PDF
Microstructure, wettability, cavitation and corrosion performance of aluminum (Al6061) coated with RF-sputtered AlN thin film
2024 · Sachin Jha, Vikrant Singh, et al. · Surface and Coatings Technology · 22
Effect of HVOF sprayed TiC+25%CuNi-Cr coatings on sustainability and cavitation erosion resistance of SS316 steel
2023 · Rampal, Anuj Bansal, et al. · CRC Press eBooks · 13
Manufacturing of Ti6Al4V alloy using argon chamber assisted WAAM-CMT to avoid oxidation and analyses of mechanical and metallurgical properties
2025 · Jonny Singla, Navin Kumar, et al. · Journal of Alloys and Compounds · 11
Influence of Post Heat Treatment on Slurry Erosion Behavior of Wire Arc Additive Manufactured (WAAMed) Inconel-625
2025 · Jonny Singla, Vikrant Singh, et al. · Key engineering materials · 11
Fabrication of Ti6Al4V alloy by wire arc additive manufacturing process and comprehensive machinability analysis
2025 · Jonny Singla, Navin Kumar, et al. · Wear · 9
Experimental research on the physical and mechanical properties of rice straw-rice straw ash composite materials
2024 · Rahul Kumar, Vikrant Singh, et al. · International Journal on Interactive Design and Manufacturing (IJIDeM) · 9
Cavitation Erosion Investigations of Hard Carbide and Nitride Based Novel Coatings Manufactured by Plasma Spraying
2024 · Pallavi Sharma, Vikrant Singh, et al. · Tribology Transactions · 8
Slurry Erosion Behavior of Ni-Al and Fe-Cr Coatings Deposited by Arc Wire Spray on Hydro Machinery SS316 Steel
2023 · Rajat Vipra, Vikrant Singh, et al. · Journal of Materials Engineering and Performance · 8
Mechanical, Metallurgical, and Cavitation–Corrosion Analysis of WC-NiCrBSi Cermet Coating Developed Via. Laser Cladding
2025 · Vikrant Singh, Deepak Kumar Goyal, et al. · Journal of Thermal Spray Technology · 4
Design and Development of High-Velocity Submerged Water Jet Cavitation Erosion Test Rig
2020 · Anuj Bansal, Jonny Singla, et al. · Lecture notes on multidisciplinary industrial engineering · 4
Effect of TiB2-B4C reinforcement and laser remelting on the microstructural, mechanical, and tribological performance of HVOF sprayed WC-10Co-4Cr coating
2026 · Anuj Bansal, Vikrant Singh, et al. · Colloids and Surfaces A Physicochemical and Engineering Aspects · 2
Investigate the Slurry Abrasion Behaviour of ERNiCrMo-3 Clads on 080M40 Steel Using a Wire Arc Additive Manufacturing Process
2025 · Ranbir Singh Rooprai, Anuj Bansal, et al. · Springer Proceedings in Materials · 2
Tribological Evaluation of Plasma-Sprayed Hydroxyapatite Coating on Wire Arc Additively Manufactured Ti6Al4V
2026 · Vikrant Singh, Anuj Bansal, et al. · Journal of Thermal Spray Technology · 1
To Study the Salt Spray Corrosion Behavior of WAAMed Cladded Inconel 625 Over EN8 Steel
2025 · Hrishav Raushan, Vikrant Singh, et al. · Springer Proceedings in Materials · 1
Investigating the Effect of Magnetic Nanoparticles in Magneto-Rheological (MR) Fluid for Monotube Damper Testing
2022 · Jonny Singla, Anuj Bansal, et al. · CRC Press eBooks · 1
Investigation of mechanical and metallurgical behaviour of WAAM-CMT-fabricated SS308L quarter iso-grid structure with and without post-deposition heat treatment
2026 · Jonny Singla, Navin Kumar, et al. · Journal of Adhesion Science and Technology
Path planning for the development of quarter iso-grid structure using wire arc additive manufacturing–cold metal transfer (WAAM–CMT): A streamlined and novel manufacturing approach
2026 · Jonny Singla, Navin Kumar, et al. · Ironmaking & Steelmaking Processes Products and Applications
Effect of Wire Arc Additive Manufacturing and Plasma-Sprayed Hydroxyapatite Coating on Ultrasonic Machining Characteristics of Ti6Al4V
2026 · Mohit Vishnoi, Anuj Bansal, et al. · Journal of Materials Engineering and Performance
Synergistic Enhancement of Mechanical and Erosion Performance in HVOF-Sprayed WC-10Co-4Cr Coatings via TiB2-B4C Hybrid Reinforcement and Laser Remelting
2026 · Jasdeep Singh, Vikrant Singh, et al. · JOM
Sustainability and machinability evaluation of drilling WAAM-CMT and Wrought Ti-6Al-4V: Comparison of three drilling tools
2026 · Navneet Khanna, Harsh Vesuwala, et al. · Cleaner Engineering and Technology
Works count: 27
Citation count: 337
H-index: 9
I10-index: 9
Year
Topic
Type