Get started
Author

Karel Doubrava

Observed names: Doubrava K., Doubrava Karel, Doubrava, K., Doubrava, Karel, K Doubrava, K. Doubrava, KAREL DOUBRAVA
Observed institutions: Universidad de Santiago de Chile, University of Maribor, Czech Aerospace Research Centre, Czech Technical University in Prague, University of Chemistry and Technology, Prague, Stanford University
ORCID: 0000-0003-2975-321X
Observed ORCID: 0000-0003-2975-321X
OpenAlex ID: A5019915979
Influence of Inherent Surface and Internal Defects on Mechanical Properties of Additively Manufactured Ti6Al4V Alloy: Comparison between Selective Laser Melting and Electron Beam Melting
2018 · Michaela Fousová, Dalibor Vojtěch, et al. · Materials · 139
Unified viscoplasticity modelling for a SiMo 4.06 cast iron under isothermal low-cycle fatigue-creep and thermo-mechanical fatigue loading conditions
2020 · Michal Bartošák, Miroslav Španiel, et al. · International Journal of Fatigue · 34
Thermo-mechanical fatigue of SiMo 4.06 turbocharger turbine housing: Damage operator approach
2019 · Michal Bartošák, Miroslav Španiel, et al. · Engineering Failure Analysis · 28
Life assessment of SiMo 4.06 cast iron under LCF and TMF loading conditions
2018 · M. Bartošák, C. Novotný, et al. · Materials at High Temperatures · 24
Use of Prandtl operators in simulating the cyclic softening of Inconel 718 under isothermal low-cycle fatigue loading
2022 · Michal Bartošák, Marko Nagode, et al. · International Journal of Mechanical Sciences · 13
PDF
A fretting damage correction factor applicable to the McDiarmid criterion of plain high‐cycle fatigue
2016 · M. Nesládek, M. Španiel, et al. · Fatigue & Fracture of Engineering Materials & Structures · 13
Experimental Development of Composite Bicycle Frame
2022 · Milan Dvořák, Tomáš Ponížil, et al. · Applied Sciences · 10
PDF
Fretting fatigue of 42CrMo4+QT steel: Experimental and numerical assessment
2024 · Martin Nesládek, Julian Marcell Enzveiler Marques, et al. · International Journal of Fatigue · 7
Multi-objective optimization of composite kayak paddle shaft through evolutionary deep learning
2025 · Bohumil Kropík, Tomáš Mareš, et al. · Materials and Manufacturing Processes · 5
Evolution control of cyclic softening of Inconel 718 under isothermal low-cycle fatigue loading by improved calculation of accumulated plastic strain
2025 · Domen Šeruga, Marko Nagode, et al. · International Journal of Pressure Vessels and Piping · 4
Verification and numerical simulation of advanced composite inlet in compliance of airworthiness impact requirements
2019 · Radek Doubrava, Martin Oberthor, et al. · 4
PDF
Loading regimes and designing helical coiled springs for safe fatigue life
2005 · M. Růžička, K. Doubrava · Research in Agricultural Engineering · 4
PDF
Testing of adhesive joints in sandwich structures
2017 · Ctirad Novotný, Karel Doubrava, et al. · Materials Today Proceedings · 3
Fatigue Behaviour of Laser Machined Aluminium Alloy 2024-T3
2011 · Růžička Milan, Doubrava Karel, et al. · Acta Mechanica Slovaca · 3
PDF
Design of Composite Hybrid Structures “on Request”
2016 · Zdeněk Pošvář, Milan Růžička, et al. · Materials Today Proceedings · 2
Fatigue behaviour and thickness effect in thin-walled welded hollow section joints: evaluation using hot-spot stress approach
2026 · Martin Machač, Jan Papuga, et al. · International Journal of Fatigue · 1
Fatigue Analysis of Thin-Walled Welded Hollow Section Joints
2022 · Martin Machač, Jan Papuga, et al. · Structural integrity · 1
Damage Detection of CFRP Filament Wound Tubes Using Electrical Resistance Measurement
2022 · Nikola Schmidová, Tomáš Ponížil, et al. · Procedia Structural Integrity · 1
Sandwich Roof of the Bus – Fatigue and Strength Tests
2016 · Karel Doubrava, Ctirad Novotný · Applied Mechanics and Materials · 1
Definition of Effective Material Properties of Recycled Plastic: Image Analysis and Homogenization
2016 · Zdenka Procházková, Vlastimil Králík, et al. · Applied Mechanics and Materials · 1
Monitoring of Crack Growth of Composite Plates using Carbon Fiber Sensors
2026 · Nikola Schmidová, Karel Doubrava, et al. · e-Journal of Nondestructive Testing
PDF
Influence of Layer Time on the Mechanical Properties of Thin-walled Parts Produced From Modified Polycarbonate Reinforced With Carbon Fibres by a Pellet Extrusion Modelling (pem) Process
2025 · M. Rytir, T. Hadrava, et al. · MM Science Journal
Monitoring of structural stiffness degradation and impact damage detection by carbon fiber sensors
2025 · Nikola Schmidová, Milan Růžička, et al. · Journal of Theoretical and Applied Mechanics/Mechanika Teoretyczna i Stosowana
PDF
Grp Tank Loading Investigation Using Cfs and Dfos Sensors
2025 · Karel Doubrava, Nikola Schmidová, et al.
PDF
Identification of the cause of damage to the firefighter ladder
2020 · Filip Průša, Vít Jonák, et al. · MANUFACTURING TECHNOLOGY
PDF
Works count: 35
Citation count: 298
H-index: 7
I10-index: 7
Year
Topic
Type