Get started
Author

Pavan Kumar Gurrala

Observed name: Pavan Gurrala
ORCID: 0000-0002-8221-3880
Observed ORCID: 0000-0002-8221-3880
OpenAlex ID: A5019944081
Part strength evolution with bonding between filaments in fused deposition modelling: This paper studies how coalescence of filaments contributes to the strength of final FDM part
2014 · Pavan Kumar Gurrala, Srinivasa Prakash Regalla · Virtual and Physical Prototyping · 271
Multi-objective optimisation of strength and volumetric shrinkage of FDM parts
2014 · Pavan Kumar Gurrala, Srinivasa Prakash Regalla · Virtual and Physical Prototyping · 125
Optimization of Support Material and Build Time in Fused Deposition Modeling (FDM)
2011 · Pavan Kumar Gurrala, Srinivasa Prakash Regalla · Applied Mechanics and Materials · 98
Influence of temperature on polymer parts manufactured by fused deposition modeling process
2019 · Deep Bhalodi, Karan Zalavadiya, et al. · Journal of the Brazilian Society of Mechanical Sciences and Engineering · 78
DOE Based Parametric Study of Volumetric Change of FDM Parts
2014 · Pavan Kumar Gurrala, Srinivasa Prakash Regalla · Procedia Materials Science · 28
PDF
Fuzzy logic based expert system for prediction of tensile strength in Fused Filament Fabrication (FFF) process
2021 · Achyut Trivedi, Pavan Kumar Gurrala · Materials Today Proceedings · 17
MoS 2 Nanostructures for Solar Hydrogen Generation via Membraneless Electrochemical Water Splitting
2023 · Khushali Joshi, Khyati Mistry, et al. · ACS Applied Electronic Materials · 15
PDF
Friction and wear rate characteristics of parts manufactured by fused deposition modelling process
2017 · Pavan Kumar Gurrala, Srinivasa Prakash Regalla · International Journal of Rapid Manufacturing · 15
Finite element studies on Triply Periodic Minimal Surfaces (TPMS)–based hip replacement implants
2024 · Jainam Moghariya, Pavan Kumar Gurrala · The International Journal of Advanced Manufacturing Technology · 13
Transient thermal finite-element analysis of fused filament fabrication process
2022 · Chitralekha Nahar, Pavan Kumar Gurrala · Rapid Prototyping Journal · 11
Effect of Ga/Al ratio on the luminescent properties of inorganic scintillating GGAG:(4 mol%)Ce ceramic powder
2024 · Nisha Oad, Divya Pandya, et al. · Ceramics International · 6
Synthesis of cerium-doped gadolinium gallium aluminum garnet (GGAG:Ce) scintillating powder via solvothermal method
2024 · Nisha Oad, Divya Pandya, et al. · Physica Scripta · 6
Novel Synthesis of radioluminescent CsI:Tl microcrystals under ambient conditions by antisolvent recrystallization method
2024 · Divya Pandya, Nisha Oad, et al. · Optical Materials · 5
Investigations on the effect of orientations on mechanical properties in fused filament fabrication parts using numerical model
2022 · Achyut Trivedi, Pavan Kumar Gurrala · Journal of the Brazilian Society of Mechanical Sciences and Engineering · 5
Numerical simulation of polymers at low and moderate strain rates
2020 · Chitralekha Nahar, Savan Sanariya, et al. · Materials Today Proceedings · 5
Finite element analysis of fused filament extrusion build part using different build orientation
2020 · Dhaval Jungivala, Pavan Kumar Gurrala · Materials Today Proceedings · 5
Parametric Study on Surface Roughness of Metallized Parts Manufactured by Additive Manufacturing
2019 · Pavan Kumar Gurrala, Brijesh Tripathi · Key engineering materials · 5
Direct air CO₂ capture using aqueous ammonia through an experimental investigation using Box-Behnken statistical approach
2025 · Neha Tiwari, K. Balamurali Krishna Mayya, et al. · Chemical Engineering Journal · 4
Investigation on electroless metallized fused filament fabricated ABS parts
2022 · Achyut Trivedi, Pavan Kumar Gurrala · Materials and Manufacturing Processes · 4
3D printed microcrystalline CsI:Tl composite scintillating thin films for X-ray imaging
2024 · Divya Pandya, Nisha Oad, et al. · Radiation Measurements · 3
PDF
A study on triply periodic minimal surfaces: A case study
2022 · Aarya Hitesh Patel, Neel Jignesh Baxi, et al. · Materials Today Proceedings · 3
Design and Manufacturing of Nasal Conformer
2018 · Kaushal Joshi, Dhara Joshi, et al. · Materials science forum · 3
Parametric Study to Predict the Bond Formation in FDM Process
2018 · Deep Vinodbhai Bhalodi, Karan Satishbhai Zalavadiya, et al. · International Journal of Materials Mechanics and Manufacturing · 3
X-ray imaging using 3D-Printed thin films of solvothermal GGAG:Ce3+ powder
2025 · Nisha Oad, Divya Pandya, et al. · Optical Materials · 2
4D Printing of Polymers
2025 · Sivanagaraju Namathoti, Pavan Kumar Gurrala, et al. · Wiley eBooks · 2
Works count: 35
Citation count: 743
H-index: 10
I10-index: 10
Year
Topic
Type