Get started
Author

Simone Venettacci

Observed names: S. Venettacci, VENETTACCI, SIMONE, Venettacci Simone
ORCID: 0000-0001-7093-0324
Observed ORCID: 0000-0001-7093-0324
OpenAlex ID: A5025069179
Environmental and Economic Analysis of FDM, SLS and MJF Additive Manufacturing Technologies
2019 · Vincenzo Tagliaferri, Federica Trovalusci, et al. · Materials · 117
PDF
Environmental assessment of Selective Laser Melting compared with Laser Cutting of 316L stainless steel: A case study for flat washers’ production
2020 · Stefano Guarino, Gennaro Salvatore Ponticelli, et al. · CIRP journal of manufacturing science and technology · 67
Laser-assisted bending of Titanium Grade-2 sheets: Experimental analysis and numerical simulation
2016 · Annamaria Gisario, Mehrshad Mehrpouya, et al. · Optics and Lasers in Engineering · 43
Improvement of thermally sprayed WC–Co/NiCr coatings by surface laser processing
2015 · A. Gisario, M. Puopolo, et al. · International Journal of Refractory Metals and Hard Materials · 40
Experimental investigation on the fatigue behavior of laser powder bed fused 316L stainless steel
2022 · Gennaro Salvatore Ponticelli, Riccardo Panciroli, et al. · CIRP journal of manufacturing science and technology · 37
Environmental and economic life cycle assessment of thermal energy storage based on organic phase change material embedded in open-cell copper foams
2021 · Simone Venettacci, Raffaello Cozzolino, et al. · Sustainable Production and Consumption · 30
Improvements in springback control by external force laser-assisted sheet bending of titanium and aluminum alloys
2016 · A. Gisario, M. Barletta, et al. · Optics & Laser Technology · 28
Re-Engineering of an Impeller for Submersible Electric Pump to Be Produced by Selective Laser Melting
2021 · Gennaro Salvatore Ponticelli, Flaviana Tagliaferri, et al. · Applied Sciences · 25
PDF
Study of the laser-material interaction for innovative hybrid structures: Thermo-mechanical characterization of polyethylene-based polymers
2023 · Mario Di Siena, Silvio Genna, et al. · Polymer Testing · 23
Progressive and constant load scratch testing of single- and multi-layered composite coatings
2013 · M. Barletta, V. Tagliaferri, et al. · Tribology International · 22
Environmental and Economic Impact of an Innovative Biocide-Free Antifouling Coating for Naval Applications
2023 · Simone Venettacci, Gennaro Salvatore Ponticelli, et al. · Materials · 21
PDF
Tribological properties of Laser Powder Bed Fused AlSi10Mg: Experimental study and statistical analysis
2022 · Simone Venettacci, Gennaro Salvatore Ponticelli, et al. · Journal of Manufacturing Processes · 21
LaserOrigami (LO) of three-dimensional (3D) components: Experimental analysis and numerical modelling
2016 · A. Gisario, M. Mehrpouya, et al. · Journal of Manufacturing Processes · 20
Progress in Tridimensional (3d) Laser Forming of Stainless Steel Sheets
2015 · Annamaria Gisario, Massimiliano Barletta, et al. · Lasers in Manufacturing and Materials Processing · 19
PDF
A comparative evaluation of fluidized bed assisted drag finishing and centrifugal disk dry finishing
2014 · M. Barletta, A. Gisario, et al. · Engineering Science and Technology an International Journal · 19
PDF
Influence of Thermal Contact Resistance of Aluminum Foams in Forced Convection: Experimental Analysis
2017 · Stefano Guarino, Giovanni Di Ilio, et al. · Materials · 18
PDF
Laser-Assisted Bending of Sharp Angles With Small Fillet Radius on Stainless Steel Sheets: Analysis of Experimental Set-Up and Processing Parameters
2015 · Annamaria Gisario, Massimiliano Barletta, et al. · Lasers in Manufacturing and Materials Processing · 18
PDF
Life cycle assessment of a new graphene-based electrodeposition process on copper components
2017 · Stefano Guarino, Nadia Ucciardello, et al. · Journal of Cleaner Production · 14
External force-assisted LaserOrigami (LO) bending: Shaping of 3D cubes and edge design of stainless steel chairs
2015 · Annamaria Gisario, Massimiliano Barletta, et al. · Journal of Manufacturing Processes · 14
New ways to the manufacturing of pigmented multi-layer protective coatings
2013 · M. Barletta, F. Trovalusci, et al. · Surface and Coatings Technology · 13
Effect of water absorption on the properties of selective laser-sintered PA12 specimens
2024 · Vittorio Villani, Gennaro Salvatore Ponticelli, et al. · Progress in Additive Manufacturing · 12
Laser-based thermomechanical joining of semi-transparent thermoplastics with technical steel
2024 · Silvio Genna, Patrizia Moretti, et al. · The International Journal of Advanced Manufacturing Technology · 11
Springback control in laser-assisted bending manufacturing process by using a fuzzy uncertain model
2020 · Gennaro Salvatore Ponticelli, Stefano Guarino, et al. · Procedia CIRP · 11
PDF
Fuzzy process optimization of laser powder bed fusion of 316L stainless steel
2022 · Gennaro Salvatore Ponticelli, Simone Venettacci, et al. · Progress in Additive Manufacturing · 10
Fused deposition modelling for aeronautics: techno-economic and environmental assessment for overhead locker supports replacement
2023 · Gennaro Salvatore Ponticelli, Simone Venettacci, et al. · The International Journal of Advanced Manufacturing Technology · 9
Works count: 50
Citation count: 732
H-index: 17
I10-index: 24
Year
Topic
Type