Get started
Author

Anouar El Magri

Observed names: A El Magri, A. EL Magri, A. El Magri, Anouar EL MAGRI, Anouar El magri
ORCID: 0000-0003-2376-0814
Observed ORCID: 0000-0003-2376-0814
OpenAlex ID: A5027189429
Optimization of printing parameters for improvement of mechanical and thermal performances of 3D printed poly(ether ether ketone) parts
2020 · Anouar El Magri, Khalil El Mabrouk, et al. · Journal of Applied Polymer Science · 181
Mechanical properties of CF-reinforced PLA parts manufactured by fused deposition modeling
2019 · Anouar El Magri, Khalil El Mabrouk, et al. · Journal of Thermoplastic Composite Materials · 175
A Combined Experimental and Computational (DFT, RDF, MC and MD) Investigation of Epoxy Resin as a Potential Corrosion Inhibitor for Mild Steel in a 0.5 M H2SO4 Environment
2023 · Rachid Hsissou, Khadija Dahmani, et al. · Polymers · 118
PDF
An overview on the influence of process parameters through the characteristic of 3D-printed PEEK and PEI parts
2021 · Anouar El Magri, Saeedeh Vanaei, et al. · High Performance Polymers · 111
3D Printed and Conventional Membranes—A Review
2022 · Baye Gueye Thiam, Anouar El Magri, et al. · Polymers · 94
PDF
Effects of Laser Power and Hatch Orientation on Final Properties of PA12 Parts Produced by Selective Laser Sintering
2022 · Anouar El Magri, Salah Eddine Bencaid, et al. · Polymers · 90
PDF
Development of new polymer composites formulated by glass as a potential protective coating for 3D printed H13 steel in acidic medium: DFT, MC and MD computational
2023 · Anouar El Magri, Rachid Hsissou, et al. · Journal of Molecular Liquids · 87
Synthesis Characterization and Highly Protective Efficiency of Tetraglycidyloxy Pentanal Epoxy Prepolymer as a Potential Corrosion Inhibitor for Mild Steel in 1 M HCl Medium
2022 · Rachid Hsissou, Redouane Lachhab, et al. · Polymers · 80
PDF
Effects of printing parameters on the tensile behavior of 3D ‐printed acrylonitrile styrene acrylate ( ASA ) material in Z direction
2022 · Anouar El Magri, Salah‐Eddine Ouassil, et al. · Polymer Engineering and Science · 80
Experimental investigation and optimization of printing parameters of 3D printed polyphenylene sulfide through response surface methodology
2020 · Anouar El Magri, Khalil El Mabrouk, et al. · Journal of Applied Polymer Science · 76
Preparation and characterization of poly(ether ether ketone)/poly(ether imide) [PEEK/PEI] blends for fused filament fabrication
2021 · Anouar El Magri, Khalil El Mabrouk, et al. · Journal of Materials Science · 58
An Investigation to Study the Effect of Process Parameters on the Strength and Fatigue Behavior of 3D-Printed PLA-Graphene
2021 · Anouar EL MAGRI, Saeedeh VANAEI, et al. · Polymers · 56
Investigating the effect of printing conditions and annealing on the porosity and tensile behavior of 3D ‐printed polyetherimide material in Z ‐direction
2022 · Salah‐Eddine Ouassil, Anouar El Magri, et al. · Journal of Applied Polymer Science · 50
Effect of printing parameters on tensile, thermal and structural properties of 3D ‐printed poly (ether ketone ketone) PEKK material using fused deposition modeling
2023 · Anouar El Magri, Sébastien Vaudreuil, et al. · Journal of Applied Polymer Science · 44
Elaboration and investigation of formulated polymer composites as some potential anticorrosion coatings for brass surface in 3.5% NaCl solution: theoretical approaches
2024 · Rachid Hsissou, Anouar El Magri, et al. · Canadian Metallurgical Quarterly · 41
Numerical–Experimental Analysis toward the Strain Rate Sensitivity of 3D-Printed Nylon Reinforced by Short Carbon Fiber
2022 · Hamid Reza Vanaei, Anouar El Magri, et al. · Materials · 37
PDF
Effects of physical and chemical ageing on 3D printed poly (ether ether ketone)/poly (ether imide) [PEEK/PEI] blend for aerospace applications
2022 · Anouar El Magri, Sébastien Vaudreuil · Journal of Materials Science · 36
Optimizing the mechanical properties of 3D-printed PLA-graphene composite using response surface methodology
2021 · A. El Magri, S. Vaudreuil · Archives of Materials Science and Engineering · 34
Printing temperature effects on the structural and mechanical performances of 3D printed Poly-(phenylene sulfide) material
2020 · A El Magri, S Vaudreuil, et al. · IOP Conference Series Materials Science and Engineering · 34
PDF
Synthesis investigation and exploring of new tetraglycidyl bisurea bisphenyl S polyepoxide as an excellent corrosion inhibitory resin for mild steel in 1M HCl environment: Comprehensive approaches
2024 · M. Azogagh, A. El Magri, et al. · Journal of Molecular Liquids · 33
Synthesis and characterization of new eco-friendly vitreous system Bi2O3–B2O3–BaO: Structural, morphologic, and thermal analysis
2024 · I. Saber, K. Dahmani, et al. · Optical Materials · 31
Orientation-Dependent Mechanical Behavior of 3D Printed Polylactic Acid Parts: An Experimental–Numerical Study
2023 · Saeedeh Vanaei, Mohammadali Rastak, et al. · Machines · 30
PDF
An overview on the progress and development of modified sulfonated polyether ether ketone membranes for vanadium redox flow battery applications
2021 · Baye Gueye Thiam, Anouar El Magri, et al. · High Performance Polymers · 30
Electrochemical, surface, and theoretical studies on amine-based organic compounds as efficient corrosion inhibitors for mild steel in 1 M HCl
2025 · Mohamed Aoulad Belayachi, Otmane Kharbouch, et al. · International Journal of Electrochemical Science · 28
Chemical composition of essential oils of Citrus limon peel from three Moroccan regions and their antioxidant, anti-inflammatory, antidiabetic and dermatoprotective properties
2022 · Meriam El Aboubi, Douae Ben Hdech, et al. · Journal of Herbmed Pharmacology · 27
PDF
Works count: 61
Citation count: 1,857
H-index: 25
I10-index: 33
Year
Topic
Type