Get started
Author

И. П. Попов

Observed names: I P Popov, I. P. Popov, I.P. Popov, Igor P. Popov, Igor Popov
ORCID: 0000-0001-6497-0004
Observed ORCID: 0000-0001-6497-0004
OpenAlex ID: A5028598467
Limits of flanging process feasibility to create thin-wall conical shells
2012 · E. G. Dem’yanenko, I. P. Popov · Russian Aeronautics · 12
Peculiarities of the process of hollow conical parts shaping from a ring blank
2010 · S. Yu. Zvonov, I. P. Popov, et al. · Russian Aeronautics · 11
Research of the process of axisymmetric forming of thin-walled flat blanks into the conical parts with minimal thickness variation
2017 · E G Demyanenko, I P Popov, et al. · IOP Conference Series Materials Science and Engineering · 8
PDF
Development of the manufacturing process of aluminum alloys with high strength and conductance
2015 · F. V. Grechnikov, E. G. Dem’yanenko, et al. · Russian Journal of Non-Ferrous Metals · 6
Directional Thickness Alteration of a Thin-Walled Ring Blank Using Flanging and Forming for the Purpose of Receiving Conical Part
2016 · E.G. Demyanenko, I.P. Popov · Key engineering materials · 5
Investigation of forming method based on flanging process
2017 · E G Demyanenko, I P Popov · IOP Conference Series Earth and Environmental Science · 4
PDF
Iterative Algorithm for Radius Stylus Compensation of Touch Sensor When Measured on CMMs of Complex Surfaces
2018 · Fedor V. Grechnikov, Igor P. Popov, et al. · International Scientific-Technical Conference on Actual Problems of Electronic Instrument Engineering (APEIE) · 3
Effect of Carbon Additives on the Mechanical Properties of a Titanium Near-α Alloy
2020 · O. S. Kashapov, T. V. Pavlova, et al. · Inorganic Materials Applied Research · 2
Researching structure heterogeneity of VT41 titanium alloy billet after thermomechanical treatment
2019 · P. N. Medvedev, S. A. Naprienko, et al. · Voprosy Materialovedeniya · 2
Simulation of plastic forming process of shells with minimal thickness fluctuations
2017 · E.G. Demyanenko, I.P. Popov, et al. · Procedia Engineering · 2
PDF
Study of thin-walled parts shaping process based on flanging and embossing
2016 · E. G. Dem’yanenko, I. P. Popov · Russian Aeronautics · 2
Study of the limiting parameters of deep drawing of sheet blanks made of heat-resistant copper alloys
2022 · E. G. Demyanenko, I. P. Popov, et al. · Izvestiya Non-Ferrous Metallurgy · 1
PDF
The Study of the Heterogeneity of the Structure of a VT41 Titanium Alloy Billet after Thermomechanical Treatment
2020 · P. N. Medvedev, S. A. Naprienko, et al. · Inorganic Materials Applied Research · 1
Investigation into the Flanging Process with Minimal Thickness Variation
2020 · E.G. Demyanenko, I.P. Popov · Materials science forum · 1
Carbon additives influence on mechanical properties of titanium near-alpha alloy
2019 · O. S. Kashapov, T. V. Pavlova, et al. · Voprosy Materialovedeniya · 1
Investigation of application of flanging process for obtaining convex parts
2018 · E G Demyanenko, I P Popov · IOP Conference Series Earth and Environmental Science · 1
PDF
Study of Thermal Resistance and Mechanical Properties of Thin Sheets of Low-Alloyed Aluminum Al-Cu-Mn and Al-Mg-Si Alloys
2016 · E.G. Demyanenko, I.P. Popov · Materials science forum · 1
Computer Model of the Method of Upsetting an Axisymmetric Shell with a Directional Change in Thickness
2026 · E. G. Dem’yanenko, K. A. Nikolenko, et al. · Russian Aeronautics
Analysis of the Features of the Clamping Bending Process in the Manufacture of Parts Consisting of Complex Curved Surfaces Using the LS-DYNA Software
2025 · K. A. Nikolenko, E. G. Dem’yanenko, et al. · Russian Aeronautics
Determination of the Area of Workpiece Destruction during the Deep Drawing into a Conical Die
2024 · E. G. Dem’yanenko, I. P. Popov, et al. · Russian Aeronautics
Improving shape formation under conditions of plane tensile stress
2023 · E. G. Demyanenko, I. P. Popov, et al. · Izvestiya Non-Ferrous Metallurgy
PDF
Modeling of the Heat Setting Process in Order to Eliminate Defects in the Obtained Part
2022 · E. G. Demyanenko, I. P. Popov, et al. · Lecture notes in mechanical engineering
ANSYS/LS-DYNA Simulation-Based Study of Buckling Caused Deep Drawing Limiting Parameters
2021 · Igor Popov, Dmitry Nikonov, et al. · International Scientific and Technical Engine Conference (EC)
Study of the process of forming large-sized thin-walled parts
2021 · E G Demyanenko, I P Popov, et al. · IOP Conference Series Materials Science and Engineering
PDF
Simulation of the combined flanging and forming process taking into account the springback effect
2019 · E G Demyanenko, A N Epifanov, et al. · Journal of Physics Conference Series
PDF
Works count: 42
Citation count: 63
H-index: 5
I10-index: 2
Year
Topic
Type