Get started
Author

Murat Beder

Observed names: M. BEDER, Murat BEDER
ORCID: 0000-0001-8117-2151
Observed ORCID: 0000-0001-8117-2151
OpenAlex ID: A5040944001
Microstructural, mechanical and tribological properties of Al–7Si–(0–5)Zn alloys
2014 · Yasin Alemdağ, Murat Beder · Materials & Design (1980-2015) · 53
Influence of Mg addition and T6 heat treatment on microstructure, mechanical and tribological properties of Al–12Si–3Cu based alloy
2021 · M. BEDER, Y. ALEMDAG · Transactions of Nonferrous Metals Society of China · 36
PDF
Effects of zinc content on strength and wear performance of Al−12Si−3Cu based alloy
2019 · Yasin ALEMDAG, Murat BEDER · Transactions of Nonferrous Metals Society of China · 32
The Effect of Heat Treatment on the Mechanical Properties and Oxidation Resistance of AlSi10Mg Alloy
2024 · Murat Beder, Serhatcan Berk Akçay, et al. · Arabian Journal for Science and Engineering · 30
PDF
Impact of high Al2O3 content on the microstructure, mechanical properties, and wear behavior Al–Cu–Mg/Al2O3 composites prepared by mechanical milling
2024 · Murat Beder, Temel Varol, et al. · Ceramics International · 22
Effects of Mn Content on Microstructure, Mechanical and Dry Sliding Wear Properties of Eutectic Al–Si–Cu Alloy
2019 · Yasin Alemdag, Murat Beder · Metals and Materials International · 19
The effect of high B4C ratio on the improvement of mechanical properties and wear resistance of Al2024/B4C composites fabricated by mechanical milling-assisted hot pressing
2025 · Murat Beder · Ceramics International · 18
Influence of post processing on the mechanical properties and wear behavior of selective laser melted Co-Cr-Mo-W alloys
2024 · Temel Varol, Hüseyin Can Aksa, et al. · Tribology International · 18
Effect of mechanical milling parameters on the properties of electrolytic pure copper powders and hot pressed billets fabricated from recycled copper wastes
2025 · Serhatcan Berk Akçay, Oğuzhan Çuvalcı, et al. · Materials Chemistry and Physics · 8
The effect of high SiC ratio on the physical, mechanical, tribological and corrosion behavior of Al2024 alloy matrix composites fabricated by powder metallurgy
2025 · Murat Beder, Temel Varol, et al. · Journal of Composite Materials · 8
Breaking the Wettability–Performance Trade-Off: Porosity-Tuned novel Ti Liquid/Gas diffusion layers for PEM water electrolyzers via selective laser melting
2026 · Serhatcan Berk Akçay, Onur Güler, et al. · Fuel · 6
Prediction of effect of fabrication parameters on the properties of B4C ceramic particle reinforced AA2024 matrix nanocomposites using neural networks
2024 · Temel Varol, Aykut Çanakçı, et al. · Materials Today Communications · 6
The effect of matrix morphology and Cu-coated SiC content on the mechanical and electrical properties of novel Cu–SiC composites
2026 · Mücahit Kocaman, Hamdullah Çuvalcı, et al. · Scientific Reports · 2
A new sustainable direct solid-state recycling of Co-Cr-Mo-W LPBF supports by mechanical milling
2026 · Temel Varol, Hüseyin Can Aksa, et al. · Powder Technology · 2
Taguchi optimization of electrolytic Cu powders recycled from scrap Cu plates and properties of recycled Cu compacts processed by hot-pressing
2026 · Mücahit Kocaman, Temel Varol, et al. · Journal of Materials Research and Technology · 1
Al-Cu-Mg Alaşımının İçyapı ve Tribolojik Özellikleri Üzerine Sıcak Presleme Yönteminin Etkisi
2024 · Murat Beder · Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi · 1
Sıcak presleme yöntemiyle üretilen AlSi10Mg alaşımının farklı presleme sıcaklıklarındaki yapı ve mekanik özelliklerinin incelenmesi
2024 · Murat Beder · Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi · 1
PDF
Çözündürme ve Yaşlandırma İşleminin Al-7Si-4Zn-3Cu Alaşımının Sürtünme ve Aşınma Özelliklerine Etkisi
2019 · Yasin Alemdağ, Murat Beder · Uluslararası mühendislik araştırma ve geliştirme dergisi · 1
PDF
Morphological, mechanical and electrical evolution of copper-coated SiC reinforced Cu matrix composites manufactured by mechanical milling and hot pressing-assisted flake powder metallurgy
2026 · Mücahit Kocaman, Hamdullah Çuvalcı, et al. · Ceramics International
A study of the wear behavior of TiSiN and AlTiCrN/TiSiN double-layer coated AISI 4140 steel
2026 · Emre Deniz Yalçın, Serhatcan Berk Akçay, et al. · Surfaces and Interfaces
The effect of heat treatment on microstructural, mechanical and tribological properties of Ti-Ag alloy produced by selective laser melting method
2026 · Serhatcan Berk Akçay, Temel Varol, et al. · Scientific Reports
PDF
Processability window and defect map for LPBF of AA2024: limits of volumetric energy density
2026 · Temel Varol, Hüseyin Can Aksa, et al. · Progress in Additive Manufacturing
Works count: 22
Citation count: 264
H-index: 8
I10-index: 8
Year
Topic
Type