Author

Alain Sarda

Observed names: A. Sarda, Alain SARDA, SARDA, Alain, Sarda Alain, Sarda, Alain

Observed institutions: Centre National de la Recherche Scientifique, Université Nantes Angers Le Mans, Instituts Universitaires de Technologie, Laboratoire de Génie des Procédés – Environnement – Agro-alimentaire, Oniris, Université de Nantes, Nantes Université

ORCID: 0009-0002-2277-8748

Observed ORCID: 0009-0002-2277-8748

OpenAlex ID: A5041128953

A knowledge based approach for elastomer cure kinetic parameters estimation

2012 · Eric Leroy, Anouar Souid, et al. · Polymer Testing · 32

Thermal Conductivity of Rubber Compounds Versus the State of Cure

2011 · Zied Cheheb, Pierre Mousseau, et al. · Macromolecular Materials and Engineering · 32

Temperature measurements in the depth and at the surface of injected thermoplastic parts

2005 · Youssef Farouq, Cécile Nicolazo, et al. · Measurement · 26

Temperature measurement and control within moulded rubber during vulcanization process

2009 · Abdulrahman El Labban, Pierre Mousseau, et al. · Measurement · 17

Pressure influence on crystallization kinetics during injection molding

2011 · Minh Cuong Le, Sofiane Belhabib, et al. · Journal of Materials Processing Technology · 16

Heat perception measurements of the different parts found in a car passenger compartment

2003 · Alain Sarda, Rémi Deterre, et al. · Measurement · 16

Influence of reversion on adhesion in the rubber-to-metal vulcanization-bonding process

2014 · Anouar Souid, Alain Sarda, et al. · Polymer Testing · 13

Change on temperature at the surface of injection moulded parts

2009 · C. Nicolazo, A. Sarda, et al. · Journal of Materials Processing Technology · 13

Biobased bitumen analogue formation during hydrothermal treatment of microalgae residues, part 2: Influence of residence time on reaction products

2020 · Antoine Rolland, Alain Sarda, et al. · Journal of Analytical and Applied Pyrolysis · 10

Rheological characterization and modelling of the rubber to metal vulcanization-bonding process

2014 · Anouar Souid, Alain Sarda, et al. · Polymer Testing · 9

Biobased bitumen analogue formation during hydrothermal treatment of microalgae residues, part 1: Influence of reaction enthalpy on the process

2020 · Antoine Rolland, Alain Sarda, et al. · Journal of Analytical and Applied Pyrolysis · 8

Temperature mapping in a two-phase water-steam horizontal flow

2018 · G. Tymen, N. Allanic, et al. · Experimental Heat Transfer · 6

Thermique de l'injection des thermoplastiques. Optimisation

2006 · Pierre MOUSSEAU, Alain SARDA, et al. · Plastiques et composites · 4

Homogeneous and Automated Cooling of a Mold Segment by Multiple Water Jet Impingement and a Cross Air Flow

2021 · Emmanuel K. K. Agyeman, Pierre Mousseau, et al. · Journal of Thermal Science and Engineering Applications · 2

Design and thermal analysis of a mold used in the injection of elastomers

2017 · Nasser Fekiri, Cécile Canto, et al. · AIP conference proceedings · 2

Optimizing Thermal Management with Regulated Jet Impingement Boiling Cooling and Transverse Airflow: A Parametric Analysis

2024 · Guerfi Djamel Eddine, Roux Stéphane, et al. · Proceedings of the World Congress on Momentum, Heat and Mass Transfer · 1

PDF

Parametric Study on Enhanced Thermal Management via Regulated Impingement Boiling Cooling

2024 · Djamel E Guerfi, Stéphane Roux, et al. · Journal of Fluid Flow Heat and Mass Transfer · 1

Kinetic of biobased bitumen synthesis from microalgae biomass by hydrothermal liquefaction

2019 · Rolland, Antoine, Sarda, Alain, et al. · HAL · 1

Etude thermique expérimentale de l’impact d’un jet d’eau sur une surface métallique concave

2019 · Agyeman, Emmanuel, Mousseau, Pierre, et al. · HAL · 1

Implementation of a parametric procedure allowing efficient positioning of heat sources: application to high-temperature composites thermoforming process

2017 · Moaine Jebara, Sofiane Belhabib, et al. · International Journal for Simulation and Multidisciplinary Design Optimization · 1

PDF

Suivre les processus et résultats de la construction de raisonnements sur des Questions Socialement Vives par des étudiants : propositions de trois variations méthodologiques

2014 · Olivier Morin, Nadia Cancian, et al. · HAL · 1

Shrinkage kinetics and thermal behaviour of injection moulded polymers

2008 · C Nicolazo, P. Vachot, et al. · International Journal of Material Forming · 1

Thermique de l’injection des thermoplastiques - Code de calcul Cat-1D

2006 · Pierre MOUSSEAU, Alain SARDA, et al. · Plastiques et composites · 1

Thermique de l'injection des thermoplastiques. Fondements

2005 · Pierre MOUSSEAU, Alain SARDA, et al. · Plastiques et composites · 1

Shape Identification and Boundary Heat Flux Determination. Application to a Phase Change Apparatus

1995 · S. Péneau, J.P. Humeau, et al. · IFAC Proceedings Volumes · 1

Works count: 45

Citation count: 217

H-index: 9

I10-index: 9