Get started
Author

R D Mera

Observed names: Mera, R., R. Mera
Observed institution: National Physical Laboratory
OpenAlex ID: A5041793445
A Review of Biaxial Test Methods for Composites
2007 · A. Smits, C. Ramault, et al. · Springer eBooks · 31
Techniques for characterising the wetting, coating and spreading of adhesives on surface.
2005 · B C Duncan, R D Mera, et al. · 22
Environmental degradation of adhesive joints: single-lap joint geometry.
1999 · W R Broughton, R D Mera, et al. · 22
Review of Durability Test Methods and Standards for Assessing Long Term Performance of Adhesive Joints
1997 · W R Broughton, R D Mera · 22
Cyclic fatigue testing of adhesive joints: test method assessment.
1999 · W R Broughton, R D Mera, et al. · 18
Environmental degradation of adhesive joints: accelerated testing.
1999 · W R Broughton, R D Mera · 14
Determination of material properties and parameters required for the simulation of impact performance of plastics using finite element analysis.
2004 · G D Dean, R D Mera · 10
Review of Life Prediction Methodology and Adhesive Joint Design and Analysis Software
1997 · W R Broughton, R D Mera · 10
Cyclic fatigue testing of adhesive joints : environmental effects.
1999 · W R Broughton, R D Mera · 8
Modeling nonlinear viscoelasticity in polymers for design using finite element analysis
2011 · G.D. Dean, L.N. McCartney, et al. · Polymer Engineering and Science · 6
Failure of flexible adhesive joints.
2001 · B C Duncan, L E Crocker, et al. · 6
Biaxial Testing of Fibre Reinforced Composites
2007 · D. Van Hemelrijck, C. Ramault, et al. · Ghent University Academic Bibliography (Ghent University) · 5
Modelling creep in toughened epoxy adhesives for finite element analysis.
2004 · G D Dean, R D Mera · 5
Creep testing of adhesive joints T-peel test.
1999 · W R Broughton, R D Mera, et al. · 5
Modelling long term deformation behaviour of polymers for finite element analysis
2009 · G. Dean, L. N. McCartney, et al. · Plastics Rubber and Composites Macromolecular Engineering · 4
Development of a Cruciform Specimen Geometry for the Characterisation of Biaxial Material Performance for Fibre Reinforced Plastics
2007 · M. Gower, R. Shaw, et al. · Springer eBooks · 2
Measurement of failure in tough plastics at high strain rates.
2005 · G D Dean, R D Mera · 2
Project PAJ3 combined cyclic loading and hostile environments 1996-1999. Report No. 1, Review of durability test methods and standards for assessing long term performance of adhesive joints.
1997 · W R Broughton, R D Mera · 2
Effects of specimen geometry on the strength of flexible adhesive joints.
2001 · W R Broughton, E Attanz, et al. · OpenGrey (Institut de l'Information Scientifique et Technique) · 1
Determining the wettability of substrates to hot melt adhesives.
2005 · R D Mera, B C Duncan
Characterising the absorbency of porous substrates.
2005 · R D Mera, B C Duncan
Round-robin validation exercise for the thick adherend shear test in compression.
2003 · R D Mera, G D Sims · OpenGrey (Institut de l'Information Scientifique et Technique)
Determination of the properties of plastics at high strain rates.
2002 · G Dean, R D Mera, et al. · OpenGrey (Institut de l'Information Scientifique et Technique)
A comparison of commercial design of experimental software programs for the analysis of durability data.
1998 · A Olusanya, K Tully, et al.
Project PAJ3 combined cyclic loading and hostile environments 1996-1999. Report No.2: review of life prediction methodology and adhesive joint design and analysis software.
1997 · W R Broughton, R D Mera
Works count: 32
Citation count: 195
H-index: 8
I10-index: 8
Year
Topic
Type