Get started
Author

Se Hun Min

Observed names: Se Hoon Min, Se hun Min, Se-Hun Min
ORCID: 0000-0002-6520-5504
Observed ORCID: 0000-0002-6520-5504
OpenAlex ID: A5050351468
Effect of Simulated-EGR (N2) on the distribution characteristics of equivalence ratio and the formation of exhaust emissions in a CI engine under early injection conditions
2019 · Se Hun Min, Hyun Kyu Suh, et al. · Energy · 17
Numerical Study on the Fuel Spray Targeting for the Improvement of HSDI Engine Performance
2016 · Se Hun Min, Hyun Kyu Suh · Transactions of the Korean Society of Mechanical Engineers B · 7
The Effect of Combustion Phase According to the Premixed Ethanol Ratio Based on the Same Total Lower Heating Value on the Formation and Oxidation of Exhaust Emissions in a Reactivity-Controlled Compression Ignition Engine
2024 · Se-Hun Min, Hyun-Kyu Suh · Fire · 4
Effect of Premixed Ethanol Ratio Based on the Same Heating Value on the Atomization of Diesel Fuel Injected in the Cylinder
2023 · Se Hun Min, And Hyun Kyu Suh · Fire · 3
PDF
Effect of Water Vapor Injection on the Distributions of Equivalence Ratio and the NO Emission Reduction in a CI Engine
2019 · Se Hun Min, Hyun Kyu Suh · Energies · 3
PDF
Effect of Cryogenic Intake Air Temperature on the In-Cylinder Temperature and Formation of Exhaust Emissions in a Compression Ignition Engine
2019 · Se Hun Min, Hyun Kyu Suh, et al. · Journal of Engineering for Gas Turbines and Power · 2
Optimization of Mixture Formation of Diesel Fuel in a Small CI Engine: The Effect of Water (H2O) Injection Into Intake Port
2017 · Se Hun Min, Jeonghyun Park, et al. · Volume 2: Emissions Control Systems; Instrumentation, Controls, and Hybrids; Numerical Simulation; Engine Design and Mechanical Development · 2
A study on the load characteristics of the asymmetry pinch yoke according to the shape of the die
2015 · Se hun Min, Hyun Kyu Suh · Journal of the Korean Society of Mechanical Technology · 2
Fuel Droplet Behavior in a Cylinder under the Difference Co2 Mole Fraction Conditions Controlled by Simulated-EGR in CI Engine
2022 · Se Hun Min, Hyun Kyu Suh · International Journal of Automotive Technology · 1
An Improvement of Production Straightness of A-IMS Tubular Shaft on According to the Number of Die Bearing
2017 · 김홍근, Se hun Min, et al. · Journal of the Korean Society of Mechanical Technology · 1
Numerical Study on the Effect of Nozzle Geometry on the Small CRDI Engine Performance
2015 · Se Hun Min, Hyun Kyu Suh · Journal of ILASS-Korea · 1
PDF
The Effect of Premixed Ethanol Ratio Based on the Same Heating Value on the Combustion and Exhaust Emissions Characteristics in the Rcci Engine for Carbon Emission Reduction
2023 · Se Hun Min, JunSang Yoo, et al. · Proceeding of Second Thermal and Fluids Engineering Conference
Comparative Analysis of Filtration and Regeneration Performance According to GPF Porous Media Material
2022 · Ju Hwan Choi, Se Hoon Min, et al. · Transactions of Korean Society of Automotive Engineers
Spray Characteristics of Diesel Fuel in a Cylinder under Cryogenic Intake Air Temperature Conditions
2021 · Se Hun Min, Suh Hyun Kyu · Journal of ILASS-Korea
Optimization of simultaneous reduction of NO and soot by using simulated‐ exhaust gas recirculation ( CO2 + N2 ) in compression ignition engine under early combustion conditions
2020 · Se Hun Min, Hyun Kyu Suh · Environmental Progress & Sustainable Energy
Effect of Reduction of Production Process in Core Partsof Aluminum IMS on Load and Stress Distributions
2020 · Se Hun Min, Suh Hyun Kyu · Journal of the Korean Society of Mechanical Technology
The Effect of Simulated-EGR (N₂+CO₂) Composition on the Distributions of Fuel Mass Fraction and Formation/Oxidation of Exhaust Emissions in a CI Engine
2019 · Se Hun Min, Junepyo Cha, et al. · Transactions of the Korean Society of Mechanical Engineers B
승용차용 알루미늄 Ims의 응력 분포 특성
2019 · Se hun Min, Hyun Kyu Suh, et al. · Journal of the Korean Society of Mechanical Technology
Improvement of Tubular Shaft Yoke Spline Machining in Both Side IMS Module
2018 · Se hun Min, Hyun Kyu Suh · Journal of the Korean Society of Mechanical Technology
A Study on the Indentation Process Improvement between Tubular Shaft Yoke and Splined Shaft in IMS Module
2018 · Se hun Min, Hyun Kyu Suh, et al. · Journal of the Korean Society of Mechanical Technology
A Study on Improvement of Spline Processing in A-IMS Tubular Shaft
2017 · 김홍근, Hyun Kyu Suh, et al. · Journal of the Korean Society of Mechanical Technology
The Effect of Sliding Cage Geometry on the A-IMS Module for Commercial Vehicle
2017 · Se hun Min, Hyun Kyu Suh · Journal of the Korean Society of Mechanical Technology
The Effect of Torque Variation on the Stress Distributions Characteristics in A-IMS for Passenger Vehicle
2016 · Se hun Min, Hyun Kyu Suh · Journal of the Korean Society of Mechanical Technology
Works count: 23
Citation count: 43
H-index: 3
I10-index: 1
Year
Topic
Type