Get started
Author

Sergey Timofeev

Observed names: S A Timofeev, S Timofeev, S. A. Timofeev, S. Timofeev, S.A. Timofeev
ORCID: 0000-0003-2412-4086
Observed ORCID: 0000-0003-2412-4086
OpenAlex ID: A5050624938
Research Results Of Stress-Strain State Of Cutting Tool When Aviation Materials Turning
2018 · A G Serebrennikova, E P Nikolaeva, et al. · Journal of Physics Conference Series · 14
PDF
Investigation of Output Parameters of Titanium Reverse Turning
2018 · A V Savilov, V M Svinin, et al. · Journal of Physics Conference Series · 10
PDF
Method of Tool Wear Control during Stainless Steel End Milling
2021 · A. S. Pyatykh, A. V. Savilov, et al. · Journal of Friction and Wear · 6
Vibration suppression methods at high performance drilling
2019 · A V Savilov, A S Pyatykh, et al. · IOP Conference Series Materials Science and Engineering · 6
PDF
Investigation of Hadfield Steel Machinability in Milling Operations
2022 · Aleksey Pyatykh, Andrey Savilov, et al. · Key engineering materials · 5
Investigation of form deviations of high-speed steel (HSS) products under turning-milling operation using automatically programmed tools
2023 · Georgiy Matlygin, Andrey Savilov, et al. · Science intensive technologies in mechanical engineering · 4
Analysis of advanced transpedicular screw machining technologies
2021 · A. V. Savilov, A. S. Pyatykh, et al. · iPolytech Journal · 4
PDF
Studies on the effect of cutter wear on cutting dynamics when turning
2020 · Sergey Timofeev, Andrey Savilov, et al. · Materials Today Proceedings · 4
An Experimental Study of Chip Shrinkage in Turning Wrought Aluminum Alloys
2022 · A. Serebrennikova, S. Timofeev · Lecture notes in mechanical engineering · 3
Studies on Titanium Alloy Turning Rate Improvement
2019 · A. V. Savilov, V. M. Svinin, et al. · Lecture notes in mechanical engineering · 3
Effect of cutting parameters on temperature in the cutting zone in a high-speed steel turn-milling process
2022 · Georgy Matlygin, Andrey Savilov, et al. · Journal of Physics Conference Series · 2
PDF
Influence of Protective Coatings of Inserts on Cutting Forces during Milling of Hadfield Steel
2023 · A. S. Pyatykh, A. V. Savilov, et al. · Journal of Friction and Wear · 1
Study of the effect of cutting modes on output parameters under high-speed steel turn-milling
2022 · D. A. Matlygin, A. V. Savilov, et al. · Advanced Engineering Research · 1
PDF
The Impact of Cutting Modes on the Output Turn-Milling Parameters for High-Speed Steel
2022 · Georgy Matlygin, Andrey Savilov, et al. · Key engineering materials · 1
Method of Tool Wear Control when Stainless Steel End Milling
2021 · A.S. Pyatykh, A.V. Savilov, et al. · Trenie i Iznos · 1
PDF
Investigation of the Quality of the Threaded Surface of Pedicle Screws
2023 · A.S. Pyatykh, S.A. Timofeev, et al. · Вестник Тамбовского государственного технического университета
The Impact of Inserts Coatings Types on Cutting Forces when Hadfield Steels Milling
2023 · A.S. Pyatykh, A.V. Savilov, et al. · Trenie i Iznos
PDF
Experimental Study of Chip Shrinkage in Turning Titanium Alloy VT6
2022 · A Pyatykh, S Timofeev · Journal of Physics Conference Series
PDF
Evaluation of the influence of a wear-resistant coating on the process of turning a titanium alloy
2022 · Aleksey Pyatykh, Sergey Timofeev · Science intensive technologies in mechanical engineering
PDF
高性能ドリル加工における振動抑制法【jst・京大機械翻訳】
2019 · A Savilov, A S Pyatykh, et al. · IOP Conference Series Materials Science and Engineering
The Study of Material Conductivity in High-performance Milling of Pockets Using Aluminum Alloy Parts
2017 · S. A. Timofeev, A. V. Savilov · Scholarly Notes of Komsomolsk-na-Amure State Technical University
PDF
Works count: 21
Citation count: 65
H-index: 5
I10-index: 2
Year
Topic
Type