Get started
Author

Sagar M. Baligidad

Observed names: Baligidad, Sagar M, SAGAR M BALIGIDAD, Sagar Baligidad, Sagar Baligidad M, Sagar M Baligidad, Sagar M Baligidad ., Sagar Mahalingappa Baligidad
Institution: CMR University
Observed institution: CMR University
ORCID: 0000-0003-2602-736X
Observed ORCID: 0000-0003-2602-736X
OpenAlex ID: A5057948034
Optimisation and environmental analysis of waste cashew nut shell oil biodiesel/cerium oxide nanoparticles blends and acetylene fumigation in agricultural diesel engine
2023 · G.M. Lionus Leo, S. Murugapoopathi, et al. · Sustainable Energy Technologies and Assessments · 50
RSM Optimization of Parameters influencing Mechanical properties in Selective Inhibition Sintering
2018 · Sagar M. Baligidad, U. Chandrasekhar, et al. · Materials Today Proceedings · 21
Fabrication of HAp/rGO nanocomposite coating on PEEK: Tribological performance study
2023 · Sagar M Baligidad, Arunkumar T, et al. · Surfaces and Interfaces · 20
Analysis of composite pressure vessel and composite overwrapped pressure vessel by analytical and finite elemental approach
2021 · G Chethan Kumar, Sagar M. Baligidad, et al. · Materials Today Proceedings · 14
Investigation on strain rate sensitivity of 3D printed sPEEK-HAP/rGO composites
2022 · Sagar M. Baligidad, G. Chethan Kumar, et al. · Journal of Manufacturing Processes · 13
PDF
Investigation on performance of hybrid coating of hydroxyapatite and reduced graphene oxide on polyether ether ketone for orthopaedic application
2023 · Sagar M. Baligidad, A. C. Maharudresh, et al. · Progress in Additive Manufacturing · 11
Taguchi’s Approach: Design optimization of process parameters in selective inhibition sintering
2018 · Sagar M. Baligidad, U. Chandrasekhar, et al. · Materials Today Proceedings · 11
Sustainable emission reduction in CI engines using cerium nanoparticles and acetylene-cedar wood oil biofuel
2024 · Gavaskar Thodda, S. Murugapoopathi, et al. · Clean Technologies and Environmental Policy · 9
Investigation on fatigue life of HAp and rGO hybrid coating on the PEEK artificial screws for dental implant
2023 · Sagar M. Baligidad, Syed Abdullah, et al. · Materials Chemistry and Physics · 8
Sand Casting: Conventional and Rapid Prototyping Manufacturing Approaches
2014 · Sagar M Baligidad . · International Journal of Research in Engineering and Technology · 8
PDF
Development and investigation of the mechanical properties of natural fiber reinforced polymer composite
2021 · G Chethan Kumar, Sagar M. Baligidad, et al. · Materials Today Proceedings · 6
Investigation of the Characteristics of Ternary Fuel Efficiency and Combustion on Dual Fuel Engines
2021 · Sagar M. Baligidad, G. Chethan Kumar, et al. · Journal of The Institution of Engineers (India) Series C · 6
Quantitative analysis of surface treatment to enhance surface finish and mechanical characteristics of ABS parts
2020 · Sagar Baligidad, Vijayananda Kaup, et al. · Applied Physics A · 6
Experimental analysis on stacking of Belleville spring
2021 · G Chethan Kumar, Sagar M. Baligidad, et al. · Materials Today Proceedings · 5
Investigation of parameters influencing mechanical properties in SIS by using RSM
2018 · Sagar M. Baligidad, U. Chandrasekhar, et al. · International Journal of Materials and Product Technology · 5
Experimental investigations on metallization in laser-sintered PA12 part using RF sputtering
2021 · Sagar M. Baligidad, G Chethan Kumar, et al. · Applied Physics A · 4
Study on the Morphological and Flexural Properties of RF Sputtered Copper Thin Film for PA12 Part
2021 · Sagar M. Baligidad, I. C. Lakshmi, et al. · Journal of The Institution of Engineers (India) Series C · 3
Effect of water absorption on mechanical and wear behavior of polyurea coating for storage tanks
2023 · T. Arunkumar, Sagar Baligidad, et al. · The International Journal of Advanced Manufacturing Technology · 2
DLC–collagen film impact on microleakage and mechanics in implants under dynamic load
2026 · Sagar M. Baligidad, M. L. J. Shruthi, et al. · Journal of Materials Science · 1
Fused filament fabrication of Stainless Steel 316L: Investigation on effect of printing parameters on microstructural and mechanical strength of sintered part
2024 · SAGAR M BALIGIDAD, BATLURI TILAK CHANDRA, et al. · International Journal of Scientific and Research Publications · 1
PDF
Thermal and mechanical characterization of OMMT nano clay treated ABS parts via acetone deposition technique
2020 · Sagar M. Baligidad, Vijayananda Kaup, et al. · Materials Today Proceedings · 1
A study on influence of process parameters on the SIS processability and mechanical properties of a HDPE
2018 · Sagar M Baligidad, U Chandrasekhar, et al. · Materials Today Proceedings · 1
Investigation of Additively Manufactured PEEK Modified With Glass Microballons as a Function of Density and Volume Fraction
2021 · Sagar Mahalingappa Baligidad, Chethan Kumar Gangadhara, et al. · Research Square
PDF
SIS Parameters Optimization and Reliable Analysis to Achieve Reduced roughness of PA12 Parts
2021 · Sagar M. Baligidad, K. Vijayananda, et al. · Journal of Advanced Manufacturing Systems
Optimization and Reliability Analysis Aiming to Minimize Surface Roughness of Selective Inhibition Sintered Parts
2020 · Sagar Baligidad, K Elangovan, et al. · SAE International Journal of Materials and Manufacturing
Works count: 28
Citation count: 206
H-index: 8
I10-index: 7
Year
Topic
Type