Get started
Author

Chris M. Taylor

Observed names: C M Taylor, C. M. Taylor, C.M. Taylor, Chris M Taylor, Chris Taylor, Christopher M Taylor, Christopher M. Taylor, Taylor, C. Martin, Taylor, C.M., Taylor, Chris M.
ORCID: 0000-0002-1325-7804
Observed ORCID: 0000-0002-1325-7804
OpenAlex ID: A5060861595
Investigation of the Influence of CO 2 Cryogenic Coolant Application on Tool Wear
2017 · Nikolaos Tapoglou, Maureen I. Aceves Lopez, et al. · Procedia CIRP · 73
PDF
Control of deviations and prediction of surface roughness from micro machining of THz waveguides using acoustic emission signals
2016 · James M. Griffin, Fernanda Diaz, et al. · Mechanical Systems and Signal Processing · 50
PDF
The role of tool geometry in process damped milling
2010 · Ahmad R. Yusoff, Sam Turner, et al. · The International Journal of Advanced Manufacturing Technology · 42
Design and manufacture of injection mould tool inserts produced using indirect SLS and machining processes
2010 · Ismet Ilyas, Chris Taylor, et al. · Rapid Prototyping Journal · 38
Chatter, process damping, and chip segmentation in turning: A signal processing approach
2010 · Christopher M Taylor, Sam Turner, et al. · Journal of Sound and Vibration · 38
Cavitation and related phenomena in lubrication : proceedings of the 1st Leeds-Lyon Symposium on Tribology held in the Institute of Tribology, Department of Mechanical Engineering, the University of Leeds, England, September 1974
1975 · D. Dowson, M. Godet, et al. · 26
Direct Selective Laser Sintering of Tool Steel Powders to High Density: Part A - Effects of Laser Beam Width and Scan Strategy
2003 · Hauser, C., Childs, T.H.C., et al. · White Rose Research Online (University of Leeds, The University of Sheffield, University of York) · 22
Milling of aerospace alloys using supercritical CO2 assisted machining
2021 · Nikolaos Tapoglou, Chris Taylor, et al. · Procedia CIRP · 19
PDF
Role of CO2 cooling strategies in managing tool wear during the shoulder milling of grade 2 commercially pure titanium
2023 · Leon Proud, Nikolaos Tapoglou, et al. · Wear · 18
PDF
Direct laser sintering of stainless steel : thermal experiments and numerical modelling
2004 · Chris Taylor · White Rose eTheses Online (University of Leeds, The University of Sheffield, University of York) · 17
Investigating the industrial impact of hydraulic oil contamination on tool wear during machining and the development of a novel quantification methodology
2020 · Thawhid Khan, Matthew Broderick, et al. · The International Journal of Advanced Manufacturing Technology · 16
PDF
Cutting fluid application for titanium alloys Ti-6Al-4V and Ti-10V-2Fe-3Al in a finish turning process
2018 · Chris M Taylor, Samantha Giovana Abrego Hernandez, et al. · Procedia CIRP · 16
PDF
The wear of non-metallic materials : proceedings of the 3rd Leeds-Lyon Symposium on Tribology held in the Institute of Tribology, Department of Mechanical Engineering, The University of Leeds, England, September 1976
1978 · D. Dowson, M. Godet, et al. · 13
Simulation and Experimental Verification of Crystalline Polymer and Direct Metal Selective Laser Sintering 100
2000 · Childs, T.H.C., Hauser, C., et al. · White Rose Research Online (University of Leeds, The University of Sheffield, University of York) · 12
Development of an enhanced single point milling procedure to screen metalworking cutting fluid performance in terms of tool wear when machining aerospace alloys
2020 · Thawhid Khan, Matthew Broderick, et al. · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · 11
PDF
Morphology of Direct SLS-Processed Stainless Steel Layers
2002 · Taylor, C. Martin, Childs, T.H.C., et al. · White Rose Research Online (University of Leeds, The University of Sheffield, University of York) · 11
Resource consumption and process performance in minimum quantity lubricated milling of tool steel
2020 · Chris M Taylor, Tom Simpson, et al. · Procedia Manufacturing · 10
PDF
Process Damping and Cutting Tool Geometry in Machining
2011 · C M Taylor, N D Sims, et al. · IOP Conference Series Materials Science and Engineering · 9
Adhesive layer formation and its dual role in tribological performance and surface integrity of Ti-6Al-4V: Implications for the machining process
2025 · Nan Xu, Dongze Wang, et al. · Tribology International · 8
Direct Selective Laser Sintering of Tool Steel Powders to High Density: Part B -The Effect on Microstructural Evolution
2003 · Akhtar, S., Wright, C.S., et al. · White Rose Research Online (University of Leeds, The University of Sheffield, University of York) · 8
The tool wear and productivity impact of CO2 and emulsion-based cooling when milling diverse titanium alloys
2025 · Leon Proud, Paul Roberts, et al. · Wear · 6
Modelling of segmentation-driven vibration in machining
2012 · Chris M. Taylor, Sam Turner, et al. · The International Journal of Advanced Manufacturing Technology · 6
Investigating the performance of 410, PH13-8Mo and 300M steels in a turning process with a focus on surface finish
2020 · Chris M. Taylor, Fernanda Díaz, et al. · Materials & Design · 5
PDF
Manufacture of Production Quality Injection Mold Tools Using SLS and HSM
2007 · C. M. Taylor, I. P. Ilyas, et al. · ASME International Manufacturing Science and Engineering Conference (MSEC) · 5
Resource-efficient performance testing of metalworking fluids utilizing single-point milling
2023 · Chris M. Taylor, Matthew Broderick, et al. · Tribology - Materials Surfaces & Interfaces · 4
Works count: 40
Citation count: 502
H-index: 13
I10-index: 17
Year
Topic
Type