Get started
Author

Michael Kitzmantel

Observed names: KITZMANTEL, Michael, Kitzmantel, Michael, M Kitzmantel, M. Kitzmantel, Michael KITZMANTEL
Observed institutions: Pennsylvania State University, AIT Austrian Institute of Technology GmbH, TU Wien, Montanuniversität Leoben, RHP Technology (Austria), ARC Seibersdorf research GmbH
ORCID: 0000-0002-2679-7818
Observed ORCID: 0000-0002-2679-7818
OpenAlex ID: A5064587376
Potential and challenges of metal-matrix-composites reinforced with carbon nanofibers and carbon nanotubes
2010 · E. Neubauer, M. Kitzmantel, et al. · Composites Science and Technology · 220
Fabrication and properties of extrusion-based 3D-printed hardmetal and cermet components
2019 · Walter Lengauer, Ivica Duretek, et al. · International Journal of Refractory Metals and Hard Materials · 187
Microstructure and mechanical properties of Ni1,5Co1,5CrFeTi0,5 high entropy alloy fabricated by mechanical alloying and spark plasma sintering
2017 · Igor Moravcik, Jan Cizek, et al. · Materials & Design · 150
Mechanical and microstructural characterization of powder metallurgy CoCrNi medium entropy alloy
2017 · Igor Moravcik, Jan Cizek, et al. · Materials Science and Engineering A · 125
Synergic strengthening by oxide and coherent precipitate dispersions in high-entropy alloy prepared by powder metallurgy
2018 · Igor Moravcik, Larissa Gouvea, et al. · Scripta Materialia · 93
Fracture and mechanical properties of lightweight alumina ceramics prepared by fused filament fabrication
2020 · M. Orlovská, Z. Chlup, et al. · Journal of the European Ceramic Society · 61
Bending Properties of Lightweight Copper Specimens with Different Infill Patterns Produced by Material Extrusion Additive Manufacturing, Solvent Debinding and Sintering
2021 · Joamin Gonzalez-Gutierrez, Santiago Cano, et al. · Applied Sciences · 57
PDF
Characterisation of sputter deposited niobium and boron interlayer in the copper–diamond system
2012 · J. Hell, M. Chirtoc, et al. · Surface and Coatings Technology · 48
PDF
Influence of sintering temperature, SiC particle size and Y 2 O 3 addition on the densification, microstructure and oxidation resistance of ZrB 2 –SiC ceramics
2016 · Z. Kováčová, Ľ. Bača, et al. · Journal of the European Ceramic Society · 47
Influence of Binder Composition and Material Extrusion (MEX) Parameters on the 3D Printing of Highly Filled Copper Feedstocks
2022 · Mahrukh Sadaf, Santiago Cano, et al. · Polymers · 41
PDF
Tailoring a Refractory High Entropy Alloy by Powder Metallurgy Process Optimization
2021 · Larissa Moravcikova-Gouvea, Igor Moravcik, et al. · Materials · 40
PDF
Material extrusion additively manufactured alumina monolithic structures to improve the efficiency of plasma-catalytic oxidation of toluene
2020 · Ting Li, Joamin Gonzalez-Gutierrez, et al. · Additive manufacturing · 27
The effect of YB4 addition in ZrB2-SiC composites on the mechanical properties and oxidation performance tested up to 2000 °C
2020 · Zuzana Kováčová, Ľubomír Orovčík, et al. · Journal of the European Ceramic Society · 27
Preparation of fully dense boron carbide ceramics by Fused Filament Fabrication (FFF)
2022 · Mária Vozárová, Erich Neubauer, et al. · Journal of the European Ceramic Society · 26
Sinterability, Mechanical Properties and Wear Behavior of Ti3SiC2 and Cr2AlC MAX Phases
2022 · Eduardo Tabares, Michael Kitzmantel, et al. · Ceramics · 25
PDF
Processing by Additive Manufacturing Based on Plasma Transferred Arc of Hastelloy in Air and Argon Atmosphere
2020 · Eva M. Perez-Soriano, Enrique Ariza, et al. · Metals · 25
PDF
Analysis of the Microstructure and Mechanical Properties of Titanium-Based Composites Reinforced by Secondary Phases and B4C Particles Produced via Direct Hot Pressing
2017 · Isabel Montealegre-Melendez, Cristina Arévalo, et al. · Materials · 25
PDF
Microstructural and XRD Analysis and Study of the Properties of the System Ti-TiAl-B4C Processed under Different Operational Conditions
2018 · Isabel Montealegre-Meléndez, Cristina Arévalo, et al. · Metals · 21
PDF
Extrusion-based additive manufacturing of Ti3SiC2 and Cr2AlC MAX phases as candidates for high temperature heat exchangers
2021 · Eduardo Tabares, Michael Kitzmantel, et al. · Journal of the European Ceramic Society · 19
Analysis of the Influence of Starting Materials and Processing Conditions on the Properties of W/Cu Alloys
2017 · Isabel Montealegre-Meléndez, Cristina Arévalo, et al. · Materials · 19
PDF
Influence of Sintering Temperature on the Microstructure and Mechanical Properties of In Situ Reinforced Titanium Composites by Inductive Hot Pressing
2016 · Cristina Arévalo, Isabel Montealegre-Meléndez, et al. · Materials · 19
PDF
Monitoring of critical processing steps during the production of high dense 3D alumina parts using Fused Filament Fabrication technology
2021 · M. Orlovská, M. Hain, et al. · Additive manufacturing · 15
Synthesis and reaction sintering of YB4 ceramics
2019 · Zuzana Kováčová, Ľuboš Bača, et al. · Ceramics International · 15
Influence of Ti on the Tensile Properties of the High-Strength Powder Metallurgy High Entropy Alloys
2020 · Igor Moravcik, Stepan Gamanov, et al. · Materials · 13
PDF
Comparative analysis of binder systems in copper feedstocks for metal extrusion additive manufacturing and metal injection moulding
2024 · Mahrukh Sadaf, Santiago Cano, et al. · Journal of Materials Research and Technology · 12
Works count: 72
Citation count: 1,494
H-index: 19
I10-index: 27
Year
Topic
Type