Get started
Author

T.T.M. Kannan

Observed names: T. T. M. Kannan, TTM. Kannan, Ttm Kannan
Institution: PRIST University
Observed institution: PRIST University
ORCID: 0000-0002-2692-4776
Observed ORCID: 0000-0002-2692-4776
OpenAlex ID: A5072283331
Recycling of plastic waste into fuel by pyrolysis - a review
2020 · Kundan Kumar Jha, T.T.M. Kannan · Materials Today Proceedings · 92
Effect of silicon carbide and silicon carbide/alumina reinforced aluminum alloy (AA6061) metal matrix composite
2021 · J. Chandradass, T. Thirugnanasambandham, et al. · Materials Today Proceedings · 52
Scope of 3D printing in manufacturing industries-A review
2021 · Bolugoddu Sandeep, T.T.M. Kannan, et al. · Materials Today Proceedings · 48
Development of computer vision for inspection of bolt using convolutional neural network
2021 · A. John Rajan, K. Jayakrishna, et al. · Materials Today Proceedings · 25
Optimization of catalytic pyrolysis process for change of plastic waste into fuel
2020 · Kundan Kumar Jha, T.T.M. Kannan, et al. · Materials Today Proceedings · 22
Influence of load and sliding speed on wear behavior of AZ91E magnesium alloy nanocomposite by dry sliding
2020 · T. Thirugnanasambandham, J. Chandradass, et al. · Materials Today Proceedings · 17
Optimization of Cylindrical Grinding Process Parameters of OHNS Steel (AISI 0-1) Rounds Using Design of Experiments Concept
2014 · M.Melwin Jagadeesh Sridhar, M Manickam, et al. · International Journal of Engineering Trends and Technology · 15
Investigation of vibration analysis during end milling process of monel alloy
2020 · Muhammed shihan, J. Chandradass, et al. · Materials Today Proceedings · 14
Alternate fuel preparation in low cost from waste plastic: A review
2020 · Kundan Kumar Jha, T.T.M. Kannan · Materials Today Proceedings · 13
Influence of blends of castor seed biodiesel and diesel on engine characteristics
2021 · Ameren Kondaiah, Y. Sesha Rao, et al. · Materials Today Proceedings · 12
Mechanical and surface morphology study of Monel – Copper joint by rotary friction welding
2020 · S. Marimuthu, K.R. Balasubramanian, et al. · Materials Today Proceedings · 9
Fuel from Plastic Waste: A Review
2020 · Kundan Kumar Jha, T. T. M. Kannan, et al. · Lecture notes in mechanical engineering · 7
Analysis and simulation of mini pyrolysis reactor for conversion of plastic waste into fuel
2021 · Kundan Kumar Jha, T.T.M. Kannan, et al. · Materials Today Proceedings · 6
Machining feasibility and sustainability study on end milling process of Monel alloy
2021 · Muhammed Shihan, J. Chandradass, et al. · Materials Today Proceedings · 3
Characteristic analysis of dissimilar metal weld for AISI304 with SA213T22 in super heater coils
2021 · K. Chandrasekaran, P. Ranjith Kumar, et al. · Materials Today Proceedings · 2
PDF
Optimization of Engine Performance through different piston shapes by Taguchi Method
2020 · V. Yalini*, TTM. Kannan, et al. · International Journal of Innovative Technology and Exploring Engineering · 2
Development of Portable Tabletop Equipments for Micromanufacturing System
2020 · T. T. M. Kannan, R. Elangovan · Lecture notes in mechanical engineering · 1
Optimization of Drilling Process Parameters on Die Steel (H13) using Carbide Coated Drill by Design of Experiment Concept
2016 · J. Ganesh, P. Renukadevi, et al. · International Journal of Advanced Engineering Research and Science · 1
PDF
Multiobjective Optimization of End Milling Process on Monel Using Grey Relational Analysis
2020 · Muhammed Shihan, J. Chandradass, et al. · Lecture notes in mechanical engineering
Evaluation of Tensile Strength of Friction Welded Monel and ETP Copper Dissimilar Joints
2020 · S. Marimuthu, K. R. Balasubramanian, et al. · Lecture notes in mechanical engineering
Design and Development of Nonautomatic Tabletop Mini Lathe
2012 · T. T. M. Kannan, P. Marimuthu · Lecture notes in mechanical engineering
The Management Accountant Inside This Issue
2011 · T.T.M. Kannan, Piyush Kumar Sinha, et al.
Works count: 22
Citation count: 341
H-index: 10
I10-index: 10
Year
Topic
Type