Get started
Author

Ahmet Yardımeden

Observed names: A. Yardimeden, Ahmet YARDIM EDEN, Ahmet Yardimeden, YARDIMEDEN, AHMET, YARDIMEDEN, Ahmet
Institution: Dicle University
Observed institution: Dicle University
ORCID: 0000-0003-2776-1195
Observed ORCID: 0000-0003-2776-1195
OpenAlex ID: A5072342525
Optimization of drilling parameters on surface roughness in drilling of AISI 1045 using response surface methodology and genetic algorithm
2010 · Erol Kilickap, Mesut Huseyinoglu, et al. · The International Journal of Advanced Manufacturing Technology · 139
Mathematical Modelling and Optimization of Cutting Force, Tool Wear and Surface Roughness by Using Artificial Neural Network and Response Surface Methodology in Milling of Ti-6242S
2017 · Erol Kilickap, Ahmet Yardimeden, et al. · Applied Sciences · 122
PDF
Selection of cutting fluids in machining processes
2007 · Orhan Çakır, Ahmet Yardımeden, et al. · Yildiz Technical University - AVESIS · 69
Investigation of experimental study of end milling of CFRP composite
2013 · Erol Kiliçkap, Ahmet Yardimeden, et al. · Science and Engineering of Composite Materials · 58
PDF
Effects of Cutting Parameters and Point Angle on Thrust Force and Delamination in Drilling of CFRP
2014 · Ahmet Yardimeden, Erol Kilickap, et al. · Materials Testing · 32
Analysis of Drilling Behaviour in Jute Fibres Reinforced Natural Composites
2022 · Burak Özdemir, Ahmet Yardimeden, et al. · Journal of Natural Fibers · 31
Optimization of parameters for drilling composite materials with freeform surfaces
2023 · Burak Ozdemir, Erol Kilickap, et al. · Materials and Manufacturing Processes · 21
A Three Dimensional Analysis of Reconstruction Plates used in Different Mandibular Defects
2010 · S. Atilgan, B. Erol, et al. · Biotechnology & Biotechnological Equipment · 21
PDF
Estimate of cutting forces and surface roughness in end milling of glass fiber reinforced plastic composites using fuzzy logic system
2013 · Yahya Hışman Çelik, Erol Kılıçkap, et al. · Science and Engineering of Composite Materials · 16
PDF
Investigation of optimum cutting parameters and tool radius in turning glass-fiber-reinforced composite material
2014 · Ahmet Yardimeden · Science and Engineering of Composite Materials · 5
Stress analysis of shrink-fitted pin-pin hole connections via Finite Element Method
2007 · Tomris Özben, Ahmet Yardımeden, et al. · Journal of Achievements of Materials and Manufacturing Engineering · 5
Estimating of cutting force and surface roughness in turning of GFRP composites with different orientation angles using artificial neural network
2022 · Ahmet Yardimeden · REVIEWS ON ADVANCED MATERIALS SCIENCE · 4
PDF
Three-Dimensional Modeling and Quantitative Assessment of Mandibular Volume in Ectodermal Dysplasia: A Case Series
2024 · Ebru Akleyin, Yasemin Yavuz, et al. · Medicina · 2
PDF
Keten Fiber Takviyeli Kompozitin Frezelenmesinde Kesme Parametrelerinin Tam Faktöriyel Tasarım ve Topsis Yöntemiyle Optimizasyonu
2023 · Mehmet Suat ALP, Yahya Hışman ÇELİK, et al. · International Journal of Innovative Engineering Applications · 2
Estimation of Forces in Longitudinal and Multi-Pass Milling of GFRP and ABACA Composites Utilizing Machine Learning Techniques
2025 · Burak Özdemir, Ender Emir, et al. · Journal of Intelligent & Fuzzy Systems · 1
An ANFIS model for predicting workpiece deformation during the milling of thin-walled composite components
2025 · Burak Özdemir, Ender Emir, et al. · Journal of Elastomers & Plastics · 1
PDF
Examining the impact of fiber orientation angle and drilling parameters on the quality of holes in GFRP pipes
2025 · Burak Ozdemir, Ender Emir, et al. · Journal of Elastomers & Plastics · 1
Biomechanical comparison of the wedge supported plates at PTO
2007 · Ahmet Yardımeden, Mehmet Halidun Keleştemur, et al. · Archives of Materials Science and Engineering · 1
Machining of natural fiber reinforced polymer composites: Damage mechanisms, fiber–process interactions, and performance implications
2026 · Yahya Hışman Çelik, Erol Kilickap, et al. · Journal of Composite Materials
Investigating Part Quality and Morphology in Machining Aluminium 7075 Alloy with Nano-Graphene Water-Based Cutting Fluid
2025 · Mohd Sayuti Ab Karim, Siti Zuliana Salleh, et al. · Lecture notes in mechanical engineering
Farklı kesme parametreleriyle AISI 1040 çeliğin tornalanmasında oluşan titreşimlerin ve yüzey pürüzlülüğün incelenmesi
2018 · Ahmet Yardımeden, Abdullah Turan · DÜMF Mühendislik Dergisi
Karbon elyaf takviyeli plastik kompozitlerin tornalanmasında yüzey pürüzlülüğü ve takım aşınmasına etki eden parametrelerin araştırılması
2017 · Erol Kılıçkap, Yahya Hışman Çelik, et al. · DÜMF Mühendislik Dergisi
PDF
AISI 1040 çeliğin tornalamasında kesme parametrelerinin kesme kuvvetine etkisi
2015 · Ahmet Yardımeden, Abdullah Turan · DÜMF Mühendislik Dergisi
The Stress Analysis of Human Tibia Under Axial Loading Using Finite Element Method
2008 · Ahmet Yardımeden, Diyarbakir Turkiye
Impacts of the structure and processing conditions on the voltage arise in machining of gray cast irons
2007 · Ahmet Yardımeden, Ali İnan, et al. · Journal of Achievements of Materials and Manufacturing Engineering
Works count: 28
Citation count: 531
H-index: 9
I10-index: 9
Year
Topic
Type