Get started
Author

Ali Oral

Observed names: A. Oral, ALİ ORAL, Ali ORAL, ORAL, ALİ, Oral, Ali
Observed institution: Balıkesir University
ORCID: 0000-0002-9144-3821
Observed ORCID: 0000-0002-9144-3821
OpenAlex ID: A5073689573
Automated cutting tool selection and cutting tool sequence optimisation for rotational parts
2003 · Ali Oral, M.Cemal Cakir · Robotics and Computer-Integrated Manufacturing · 44
Design Optimization of Magnetic Flux Distribution for PMG by Using Response Surface Methodology
2020 · Aslan Deniz Karaoglan, Demet Gonen Ocaktan, et al. · IEEE Transactions on Magnetics · 17
Computer-assisted robotic tiling of mosaics
2004 · Ali Oral, Fehmi Erzincanlı · Robotica · 17
Surface roughness analysis of greater cutting depths during hard turning
2017 · Dilek Murat, Cihat Ensarioglu, et al. · Materials Testing · 15
Marble mosaic tiling automation with a four degrees of freedom Cartesian robot
2008 · Ali Oral, Esra Pınar Inal · Robotics and Computer-Integrated Manufacturing · 14
Bir Transformatör İşletmesinde Montaj Ünitesinin Ergonomik Analizi
2017 · Demet GÖNEN, Ali ORAL, et al. · Sakarya University Journal of Science · 11
PDF
Computer‐Aided Ergonomic Analysis for Assembly Unit of an Agricultural Device
2016 · Demet Gonen, Ali Oral, et al. · Human Factors and Ergonomics in Manufacturing & Service Industries · 10
Patterning automation of square mosaics using computer assisted SCARA robot
2009 · Ali Oral · Robotica · 10
Kas iskelet sistemi rahatsızlıklarının analizinde yeni bir risk değerlendirme yaklaşımı
2018 · Demet GÖNEN, Aslan Deniz KARAOGLAN, et al. · Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi · 7
PDF
Maki̇na Montajinda Zaman İsrafinin Kaldirilmasi İçi̇n Reba Ve Muri̇ Çalişmasi
2018 · Ali Oral, Demet Gönen, et al. · Mühendislik Bilimleri ve Tasarım Dergisi · 6
Ot Toplama Tırmığı Montaj İşleminde Çalışma Duruşlarının Anybody Modelleme Sistemi ile Analizi
2017 · Ali ORAL, Demet GÖNEN, et al. · Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi · 6
PDF
Ergonomic Analysis of an Assembly Line Using the AnyBody Modeling System
2017 · Hilal Atici, Demet Gonen, et al. · Proceedings of the World Congress on Mechanical, Chemical, and Material Engineering · 6
PDF
Optimisation of machining parameters of AISI 304L stainless steel with the least error method using Taguchi, RSM, and ANN
2024 · Yunus Emre Nehri, Ali Oral, et al. · Australian Journal of Mechanical Engineering · 5
Tekrarlanan işlerde algılanan zihinsel iş yükü
2020 · Demet GÖNEN OCAKTAN, Aslan Deniz KARAOĞLAN, et al. · Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi · 5
PDF
Experimental investigation of a novel machining strategy for rough turning using variable feed rate
2016 · Ali Oral, M. Cemal Cakir, et al. · The International Journal of Advanced Manufacturing Technology · 5
Investigating the benefits of using circular die springs instead of rectangular die springs
2015 · D. Gonen, A. Oral, et al. · Fatigue & Fracture of Engineering Materials & Structures · 5
Çalişanlarda Zorlanmaya Neden Olan Duruşlarin Reba Yöntemi̇ İle Ergonomi̇k Anali̇zi̇
2015 · Hilal ATICI, Demet Gönen, et al. · Mühendislik Bilimleri ve Tasarım Dergisi · 4
PDF
Sert malzemelerin tornalanmasında takım aşınmasının tepki yüzeyi metodolojisi ile incelenmesi
2018 · Ali ORAL · Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi · 3
PDF
Investigation of the effects of atmospheric pressure cold and hot plasma on the adhesive bond strength of Al 5049 and CFRP
2025 · Yunus Emre Nehri, Ali Oral, et al. · Materials Research Express · 2
PDF
DIN 1.2379 soğuk iş takım çeliğinin değişken ilerlemeli tornalanmasında serbest yüzey aşınmasının deneysel olarak incelenmesi, değişken ilerleme seviyelerinin optimizasyonu
2022 · Berna İMREK, Ali ORAL · Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi · 2
PDF
Magnetic Flux Density Distribution of 1.5 kW Permanent Magnet Synchronous Generator by using Response Surface Methodology
2021 · Deniz Perin, Mehmet Baki Dogru, et al. · Proceedings of the World Congress on Mechanical, Chemical, and Material Engineering · 1
PDF
Scheduling Customized Orders by Considering the Ergonomic Constraints: A Case Study at YEMTAR Company
2018 · A. Deniz Karaoglan, M. A. Beyazit Ocaktan, et al. · Proceedings of the World Congress on Mechanical, Chemical, and Material Engineering · 1
PDF
Depolama Alanlarinda Çalişanlarin Çalişma Pozi̇syonlarinin İncelenmesi̇
2017 · Demet GÖNEN, Hilal ATICI, et al. · Mühendislik Bilimleri ve Tasarım Dergisi · 1
Investigation of the effect of sanding parameters on surface roughness of S235 steel and PP plastic by response surface method and artificial neural networks
2026 · Yunus Emre Nehri, Melih Sarılıgil, et al. · Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
PDF
Experimental, numerical, and multi-objective optimization analysis of atmospheric pressure cold plasma treatment on aluminum 7075 T6-CFRP adhesive joints
2026 · Yunus Emre Nehri, Ali Oral, et al. · Materials Testing
Works count: 57
Citation count: 197
H-index: 8
I10-index: 8
Year
Topic
Type