Get started
Author

İbrahim Çiftçi

Observed names: Ibrahim Ciftci, Çiftci İbrahim, İ Çiftçi, İBRAHİM ÇİFTÇİ, İbrahim ÇİFTÇİ
Observed institutions: Aksaray University, Karabük University, Türkiye Bilimsel ve Teknolojik Araştırma Kurumu, Çankırı Karatekin University, Hacettepe University, Gazi University
ORCID: 0000-0001-7875-6324
Observed ORCID: 0000-0001-7875-6324
OpenAlex ID: A5075407010
Determination of optimum cutting parameters during machining of AISI 304 austenitic stainless steel
2003 · Ihsan Korkut, Mustafa Kasap, et al. · Materials & Design (1980-2015) · 276
Machining of austenitic stainless steels using CVD multi-layer coated cemented carbide tools
2005 · Ibrahim Ciftci · Tribology International · 227
Evaluation of tool wear when machining SiCp-reinforced Al-2014 alloy matrix composites
2003 · Ibrahim Ciftci, Mehmet Turker, et al. · Materials & Design (1980-2015) · 185
CBN cutting tool wear during machining of particulate reinforced MMCs
2004 · Ibrahim Ciftci, Mehmet Turker, et al. · Wear · 113
Design and construction of a dynamometer for measurement of cutting forces during machining with linear motion
2002 · Ulvi Şeker, Abdullah Kurt, et al. · Materials & Design (1980-2015) · 51
Experimental investigation and prediction of wear properties of Al/SiC metal matrix composites produced by thixomoulding method using Artificial Neural Networks
2014 · Dursun Özyürek, Ali Kalyon, et al. · Materials & Design (1980-2015) · 50
The effect of alloying elements on surface roughness and cutting forces during machining of ductile iron
2003 · Ulvi Şeker, İbrahim Çiftçi, et al. · Materials & Design (1980-2015) · 41
An Investigation into the Influences of Grain Size and Grinding Parameters on Surface Roughness and Grinding Forces when Grinding
2010 · Halil Demir, Abdulkadir Güllü, et al. · Strojniški vestnik – Journal of Mechanical Engineering · 38
The effect of feed rate on the cutting forces when machining with linear motion
2004 · Ulvi Şeker, Abdullah Kurt, et al. · Journal of Materials Processing Technology · 35
Investigation of the effects of drill geometry on drilling performance and hole quality
2020 · Mehtap Yavuz, Hüseyin Gökçe, et al. · The International Journal of Advanced Manufacturing Technology · 34
An investigation into the wear behaviour of TiB 2 particle reinforced aluminium composites produced by mechanical alloying
2011 · Dursun Ozyurek, Ibrahim Ciftci · Science and Engineering of Composite Materials · 31
PDF
Cutting parameter optimization in shoulder milling of commercially pure molybdenum
2018 · Hüseyin Gökçe, İbrahim Çiftçi, et al. · Journal of the Brazilian Society of Mechanical Sciences and Engineering · 27
The tribological properties of A356-SiC p metal-matrix composites fabricated by thixomoulding technique
2012 · Dursun Özyürek, Musa Yıldırım, et al. · Science and Engineering of Composite Materials · 25
PDF
Synthesis, Characterization and Dry Sliding Wear Behavior of In-situ Formed TiAl3 Precipitate Reinforced A356 Alloy Produced by Mechanical Alloying Method
2015 · Özyürek Dursun, Tuncay Tansel, et al. · Materials Research · 22
PDF
Molibden alaşımlarının işlenmesinde kesici takım ve kesme parametrelerinin Taguchi Metodu ile optimizasyonu
2018 · İBRAHİM ÇİFTÇİ, HÜSEYİN GÖKÇE · Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi · 21
PDF
Experimental investigation and modelling of surface roughness and resultant cutting force in hard turning of AISI H13 Steel
2016 · M Boy, N Yaşar, et al. · IOP Conference Series Materials Science and Engineering · 16
PDF
Mg2Si partikül takviyeli magnezyum alaşımlarının tornalanmasında yüzey pürüzlülüğünün optimizasyonu
2018 · Mahir Akgün, Halil Demir, et al. · Journal of Polytechnic · 12
PDF
The Influence of Chip Breaker Geometry on Tool Stresses in Turning
2011 · Huseyin Gurbuz, Abdullah Kurt, et al. · Strojniški vestnik – Journal of Mechanical Engineering · 12
PDF
The Effect of Aging and Sliding Speed on Wear Behaviour of Cu-Cr-Zr Alloy
2013 · Dursun Özyürek, Ibrahim Ciftci, et al. · Materials Testing · 11
Application of the Taguchi method to optimize the cutting conditions in hard turning of a ring bore
2015 · Mehmet Boy, Ibrahim Ciftci, et al. · Materiali in tehnologije · 8
PDF
AISI P20S Kalıp Çeliğinin İşlenebilirliğinin İncelenmesi
2021 · Mücahit COŞKUN, İbrahim ÇİFTÇİ, et al. · İmalat Teknolojileri ve Uygulamaları · 6
PDF
Frezeleme Operasyonlarında Kesme Kuvvetlerinin Deneysel ve Sonlu Elemanlar Analizi ile İncelenmesi: Saf Molibdenin İşlenmesi Üzerine Bir Çalışma
2019 · Hüseyin GÖKÇE, İbrahim Çiftçi, et al. · Journal of Polytechnic · 6
PDF
Mathematical Modelling and Multiresponse Optimization to Minimize Surface Roughness in Drilling Custom 450 Stainless Steel
2023 · Hüseyin GÖKÇE, İbrahim ÇİFTÇİ · İmalat Teknolojileri ve Uygulamaları · 5
PDF
Ti6Al4V Titanyum Alaşımının Delinmesinde Delme Yönteminin Aşınmaya Etkisinin İncelenmesi
2018 · İbrahim Çiftçi, Hüseyin Gökçe · Journal of Polytechnic · 5
Innovative hybrid drill bit that accelerates heat conduction: Its design, manufacturing and test
2024 · Hüseyin Gökçe, İbrahim Çiftçi · Journal of Manufacturing Processes · 3
Works count: 34
Citation count: 1,274
H-index: 16
I10-index: 19
Year
Topic
Type