Get started
Author

E. G. Dem’yanenko

Observed names: E G Demyanenko, E. G. Demyanenko, E.G. Demyanenko, Elena Demyanenko
ORCID: 0000-0003-2518-9762
Observed ORCID: 0000-0003-2518-9762
OpenAlex ID: A5079346436
Limits of flanging process feasibility to create thin-wall conical shells
2012 · E. G. Dem’yanenko, I. P. Popov · Russian Aeronautics · 12
A technique of shaping the barrel-type parts
2014 · E. G. Dem’yanenko · Russian Aeronautics · 10
Research of the process of axisymmetric forming of thin-walled flat blanks into the conical parts with minimal thickness variation
2017 · E G Demyanenko, I P Popov, et al. · IOP Conference Series Materials Science and Engineering · 8
PDF
Development of the manufacturing process of aluminum alloys with high strength and conductance
2015 · F. V. Grechnikov, E. G. Dem’yanenko, et al. · Russian Journal of Non-Ferrous Metals · 6
Directional Thickness Alteration of a Thin-Walled Ring Blank Using Flanging and Forming for the Purpose of Receiving Conical Part
2016 · E.G. Demyanenko, I.P. Popov · Key engineering materials · 5
Investigation of forming method based on flanging process
2017 · E G Demyanenko, I P Popov · IOP Conference Series Earth and Environmental Science · 4
PDF
Simulation of plastic forming process of shells with minimal thickness fluctuations
2017 · E.G. Demyanenko, I.P. Popov, et al. · Procedia Engineering · 2
PDF
Study of thin-walled parts shaping process based on flanging and embossing
2016 · E. G. Dem’yanenko, I. P. Popov · Russian Aeronautics · 2
Study of the limiting parameters of deep drawing of sheet blanks made of heat-resistant copper alloys
2022 · E. G. Demyanenko, I. P. Popov, et al. · Izvestiya Non-Ferrous Metallurgy · 1
PDF
Investigation into the Flanging Process with Minimal Thickness Variation
2020 · E.G. Demyanenko, I.P. Popov · Materials science forum · 1
Investigation of application of flanging process for obtaining convex parts
2018 · E G Demyanenko, I P Popov · IOP Conference Series Earth and Environmental Science · 1
PDF
Study of Thermal Resistance and Mechanical Properties of Thin Sheets of Low-Alloyed Aluminum Al-Cu-Mn and Al-Mg-Si Alloys
2016 · E.G. Demyanenko, I.P. Popov · Materials science forum · 1
Computer Model of the Method of Upsetting an Axisymmetric Shell with a Directional Change in Thickness
2026 · E. G. Dem’yanenko, K. A. Nikolenko, et al. · Russian Aeronautics
Analysis of the Features of the Clamping Bending Process in the Manufacture of Parts Consisting of Complex Curved Surfaces Using the LS-DYNA Software
2025 · K. A. Nikolenko, E. G. Dem’yanenko, et al. · Russian Aeronautics
Investigation of the Drawing Process for Obtaining the Spherical Bottoms
2025 · E. G. Dem’yanenko, Yu. S. Okhapkin · Russian Aeronautics
Deep Drawing of Spherical Bottoms with Minimal Thinning
2024 · E. G. Dem’yanenko, Yu. S. Okhapkin · Russian Aeronautics
Determination of the Area of Workpiece Destruction during the Deep Drawing into a Conical Die
2024 · E. G. Dem’yanenko, I. P. Popov, et al. · Russian Aeronautics
Improving shape formation under conditions of plane tensile stress
2023 · E. G. Demyanenko, I. P. Popov, et al. · Izvestiya Non-Ferrous Metallurgy
PDF
Improving the Molding Process to Obtain Thin-Walled Axisymmetric Parts of a Truncated Tapering Shape
2023 · E. G. Dem’yanenko, A. A. Levagina · Russian Aeronautics
Modeling of the Heat Setting Process in Order to Eliminate Defects in the Obtained Part
2022 · E. G. Demyanenko, I. P. Popov, et al. · Lecture notes in mechanical engineering
ANSYS/LS-DYNA Simulation-Based Study of Buckling Caused Deep Drawing Limiting Parameters
2021 · Igor Popov, Dmitry Nikonov, et al. · International Scientific and Technical Engine Conference (EC)
Study of the process of forming large-sized thin-walled parts
2021 · E G Demyanenko, I P Popov, et al. · IOP Conference Series Materials Science and Engineering
PDF
Simulation of the combined flanging and forming process taking into account the springback effect
2019 · E G Demyanenko, A N Epifanov, et al. · Journal of Physics Conference Series
PDF
Development of a mathematical model of operation forming with discounting assumption about the flat-deformed state
2019 · E G Demyanenko, A Yu Kosolapova · Journal of Physics Conference Series
PDF
Simulation of plastic forming process by variation of geometric parameters
2019 · E G Demyanenko, A N Epifanov, et al. · Journal of Physics Conference Series
PDF
Works count: 31
Citation count: 53
H-index: 5
I10-index: 2
Year
Topic
Type