Get started
Author

José Luis Cantero

Observed names: J. L. Cantero, J.L. Cantero, JOSÉ LUIS CANTERO GUISANDEZ, José Cantero, José L Cantero, José Luis Cantero Guisández, José-Luis Cantero
Observed institution: Universidad Carlos III de Madrid
ORCID: 0000-0001-7247-8589
Observed ORCID: 0000-0001-7247-8589
OpenAlex ID: A5083152534
Analysis of tool wear patterns in finishing turning of Inconel 718
2012 · J.L. Cantero, J. Díaz-Álvarez, et al. · Wear · 227
PDF
Dry drilling of alloy Ti–6Al–4V
2005 · J.L. Cantero, M.M. Tardío, et al. · International Journal of Machine Tools and Manufacture · 200
PDF
Experimental Analysis of the Influence of Drill Point Angle and Wear on the Drilling of Woven CFRPs
2014 · Norberto Feito, José Díaz-Álvarez, et al. · Materials · 97
PDF
Numerical analysis of the tool wear effect in the machining induced residual stresses
2010 · A. Muñoz-Sánchez, J.A. Canteli, et al. · Simulation Modelling Practice and Theory · 71
Machine learning approach in non-intrusive monitoring of tool wear evolution in massive CFRP automatic drilling processes in the aircraft industry
2022 · C. Domínguez-Monferrer, J. Fernández-Pérez, et al. · Journal of Manufacturing Systems · 70
PDF
Influence of cutting parameters on tool wear and hole quality in composite aerospace components drilling
2017 · J. Fernández-Pérez, J.L. Cantero, et al. · Composite Structures · 68
PDF
Numerical analysis of thermomechanical phenomena influencing tool wear in finishing turning of Inconel 718
2014 · J. Díaz-Álvarez, J.L. Cantero, et al. · International Journal of Mechanical Sciences · 58
Combined analysis of wear mechanisms and delamination in CFRP drilling
2020 · J. Fernández-Pérez, J. Díaz-Álvarez, et al. · Composite Structures · 53
PDF
Experimental analysis of special tool geometries when drilling woven and multidirectional CFRPs
2015 · Norberto Feito, Antonio Diaz-Álvarez, et al. · Journal of Reinforced Plastics and Composites · 51
High Speed Finish Turning of Inconel 718 Using PCBN Tools under Dry Conditions
2018 · José Cantero, José Díaz-Álvarez, et al. · Metals · 48
PDF
Cutting performance of TiCN–HSS cermet in dry machining
2009 · J.A. Canteli, J.L. Cantero, et al. · Journal of Materials Processing Technology · 43
Hybrid Composite-Metal Stack Drilling with Different Minimum Quantity Lubrication Levels
2019 · J. Fernández-Pérez, J. L. Cantero, et al. · Materials · 41
PDF
Influence of Special Tool Geometry in Drilling Woven CFRPs Materials
2015 · N. Feito, J. Díaz Álvarez, et al. · Procedia Engineering · 32
PDF
Spot-checking machine learning algorithms for tool wear monitoring in automatic drilling operations in CFRP/Ti6Al4V/Al stacks in the aircraft industry
2024 · C. Domínguez-Monferrer, A. Ramajo-Ballester, et al. · Journal of Manufacturing Systems · 30
PCBN Performance in High Speed Finishing Turning of Inconel 718
2018 · José Díaz-Álvarez, Víctor Criado, et al. · Metals · 28
PDF
Multiresolution analysis for tool failure detection in CFRP/Ti6Al4V hybrid stacks drilling in aircraft assembly lines
2023 · C. Domínguez-Monferrer, A. Guerra-Sancho, et al. · Mechanical Systems and Signal Processing · 21
Study of the performance of PCBN and carbide tools in finishing machining of Inconel 718 with cutting fluid at conventional pressures
2018 · Víctor Criado, José Díaz-Álvarez, et al. · Procedia CIRP · 18
PDF
Finishing Turning of Ni Superalloy Haynes 282
2018 · José Díaz-Álvarez, Antonio Díaz-Álvarez, et al. · Metals · 17
PDF
An efficient implementation of boundary conditions in an ALE model for orthogonal cutting
2009 · María Henar Miguélez, Ana Muñoz-Sánchez, et al. · 16
CFRP drilling process control based on spindle power consumption from real production data in the aircraft industry
2022 · C. Domínguez-Monferrer, J. Fernández-Pérez, et al. · Procedia CIRP · 15
PDF
Thermo-Viscoplastic Behavior of Ni-Based Superalloy Haynes 282 and Its Application to Machining Simulation
2017 · Marcos Rodríguez-Millán, José Díaz-Álvarez, et al. · Metals · 15
PDF
Analysis of orthogonal cutting of biocomposites
2019 · A. Díaz-Álvarez, J. Díaz-Álvarez, et al. · Composite Structures · 14
Sustainable High-Speed Finishing Turning of Haynes 282 Using Carbide Tools in Dry Conditions
2019 · Antonio Díaz-Álvarez, José Díaz-Álvarez, et al. · Metals · 14
PDF
A New Cutting Device Design to Study the Orthogonal Cutting of CFRP Laminates at Different Cutting Speeds
2019 · Víctor Criado, Norberto Feito, et al. · Materials · 13
PDF
Analysis of Tool Wear and Hole Delamination for Large-Diameter Drilling of CFRP Aircraft Fuselage Components: Identifying Performance Improvement Drivers and Optimization Opportunities
2023 · Juan Fernández-Pérez, Carlos Domínguez-Monferrer, et al. · Journal of Manufacturing and Materials Processing · 12
PDF
Works count: 49
Citation count: 1,341
H-index: 17
I10-index: 27
Year
Topic
Type