Get started
Author

Shunuan Liu

Observed names: LIU Shunuan, Liu Shunuan, Shunuan LIU
ORCID: 0000-0002-2136-1839
Observed ORCID: 0000-0002-2136-1839
OpenAlex ID: A5084913286
Critical thrust force predicting modeling for delamination-free drilling of metal-FRP stacks
2013 · Zhenchao Qi, Kaifu Zhang, et al. · Composite Structures · 88
Investigation on the interface damage in drilling low-stiffness CFRP/Ti stacks
2019 · Bin LUO, Kaifu ZHANG, et al. · Chinese Journal of Aeronautics · 66
Research on key technologies of fault diagnosis and early warning for high-end equipment based on intelligent manufacturing and Internet of Things
2019 · Miao Wang, Zhenming Zhang, et al. · The International Journal of Advanced Manufacturing Technology · 49
Fretting behaviors of interface between CFRP and coated titanium alloy in composite interference-fit joints under service condition
2017 · Junshan Hu, Kaifu Zhang, et al. · Materials & Design · 47
A novel prediction model for thrust force and torque in drilling interface region of CFRP/Ti stacks
2015 · Bin Luo, Yuan Li, et al. · The International Journal of Advanced Manufacturing Technology · 47
Synthesized silver nanoparticles decorated reduced graphene oxide/silver ink for aerosol jet printed conformal temperature sensor with a wide sensing range and excellent stability
2023 · Yingjie Niu, Yufei Han, et al. · Journal of Materials Research and Technology · 44
An analytical method for predicting the fluctuation of thrust force during drilling of unidirectional carbon fiber reinforced plastics
2014 · Qingxun Meng, Kaifu Zhang, et al. · Journal of Composite Materials · 42
Investigation of CFRP damages induced by the interface high temperature and mixed tool wear mechanism in drilling of thin-walled CFRP /Ti stacks
2023 · Sipeng Cao, Yuan Li, et al. · Composite Structures · 38
A review on the cutting of carbon fiber reinforced thermoplastic composites
2024 · Zhijian Meng, Shunuan Liu, et al. · Polymer Composites · 36
A comparative study on drilling characteristics of unidirectional thermosetting CF/epoxy and thermoplastic CF/PEEK composites
2024 · Zhijian Meng, Shunuan Liu, et al. · Composite Structures · 34
A typical process route discovery method based on clustering analysis
2006 · Shunuan Liu, Zhenming Zhang, et al. · The International Journal of Advanced Manufacturing Technology · 26
Effect of workpiece stiffness on thrust force and delamination in drilling thin composite laminates
2015 · Bin Luo, Yuan Li, et al. · Journal of Composite Materials · 23
Modelling of thrust force for worn drill bits characterised by cutting edge radius in drilling carbon fibre–reinforced plastic/Ti-6Al-4V alloy stacks
2017 · Bin Luo, Kaifu Zhang, et al. · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · 19
Feasibility study and prospects analysis of lunar regolith forming based on concentrated solar energy
2025 · Honglun Yang, Haitao Wang, et al. · Acta Astronautica · 13
On full life-cycle instantaneous force predicting when drilling CFRP-metal stacks
2016 · Liu Shunuan, Qi Zhenchao, et al. · The International Journal of Advanced Manufacturing Technology · 12
A subjective-objective evaluation method of hole surface quality in drilling CFRP-Ti stacks
2020 · Shunuan Liu, Ning Wang, et al. · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · 11
Sequential homogenization in Laplace Domain for viscoelastic properties of composites with functionally graded interphase
2020 · Shunuan Liu, Yi Cheng, et al. · Composite Structures · 8
Strain rate dependent material removal mechanism and surface morphology formation mechanism for high strength CFRTP
2025 · Kuangqing Hu, Shunuan Liu, et al. · Materials & Design · 7
Investigation on Hole Quality and Tool Wear of CFRP Drilling With Cryogenic‐Minimal Quantity Lubrication
2025 · Tao Wang, Shunuan Liu, et al. · Polymer Composites · 7
PDF
Effect of cooling temperature on machinability and hole quality in cryogenic drilling of CFRP/Ti stacks
2025 · Shunuan Liu, Zhijian Meng, et al. · Journal of Materials Research and Technology · 7
Multi-objective Drilling Parameters Optimization Method for CFRP/Ti Stacks
2020 · LIU Shunuan, XIA Wenqiang, et al. · Journal of Mechanical Engineering · 6
PDF
The Simulation on Drilling of Carbon Fiber Reinforced Plastic Composites
2012 · Fei Gao, Xitian Tian, et al. · International Conference on Computer Application and System Modeling · 6
PDF
A comparative study on conventional drilling and ultrasonic vibration-assisted drilling of CF/PEEK
2026 · Shiming Liang, Zhenming Zhang, et al. · Composite Structures · 5
Investigation on entrance and exit delamination damage in drilling CF/PEEK via experimental and machine learning approaches
2026 · Zhijian Meng, Shunuan Liu, et al. · Thin-Walled Structures · 5
Study on the Surface Roughness of Transitional Field in Drilling CFRP/Ti Stacks
2021 · LIU Shunuan, SONG Ye, et al. · Journal of Mechanical Engineering · 5
PDF
Works count: 50
Citation count: 671
H-index: 13
I10-index: 16
Year
Topic
Type