Get started
Author

Hüseyin Can Aksa

Observed names: Huseyin Can Aksa, Hüseyin Can AKSA
Observed institution: Karadeniz Technical University
ORCID: 0000-0001-9086-6526
Observed ORCID: 0000-0001-9086-6526
OpenAlex ID: A5090844752
The effect of silver coated copper particle content on the properties of novel Cu-Ag alloys prepared by hot pressing method
2021 · Temel Varol, Onur Güler, et al. · Powder Technology · 86
Effects of fabrication parameters and post-processing treatments on the mechanical and tribological behavior of surface-enhanced copper based materials by selective laser melting
2022 · Hüseyin Can Aksa, İlyas Hacısalihoğlu, et al. · Journal of Materials Processing Technology · 42
The Effect of Selective Laser Melting Process on the Microstructure, Density, and Electrical Conductivity of Silver-Coated Copper Cores
2021 · Temel Varol, İlyas Hacısalihoğlu, et al. · Journal of Materials Engineering and Performance · 32
Novel advanced copper-silver materials produced from recycled dendritic copper powders using electroless coating and hot pressing
2022 · Temel Varol, Onur Güler, et al. · Powder Metallurgy · 19
Influence of post processing on the mechanical properties and wear behavior of selective laser melted Co-Cr-Mo-W alloys
2024 · Temel Varol, Hüseyin Can Aksa, et al. · Tribology International · 18
Effect of mechanical milling parameters on the properties of electrolytic pure copper powders and hot pressed billets fabricated from recycled copper wastes
2025 · Serhatcan Berk Akçay, Oğuzhan Çuvalcı, et al. · Materials Chemistry and Physics · 8
Breaking the Wettability–Performance Trade-Off: Porosity-Tuned novel Ti Liquid/Gas diffusion layers for PEM water electrolyzers via selective laser melting
2026 · Serhatcan Berk Akçay, Onur Güler, et al. · Fuel · 6
Bor Karbür Takviyeli Al Esaslı Kompozitlerin Özellikleri Üzerine Bor Karbür Takviye Miktarının Etkisi
2022 · Serhatcan Berk AKÇAY, Temel VAROL, et al. · El-Cezeri Fen ve Mühendislik Dergisi · 4
The effect of matrix morphology and Cu-coated SiC content on the mechanical and electrical properties of novel Cu–SiC composites
2026 · Mücahit Kocaman, Hamdullah Çuvalcı, et al. · Scientific Reports · 2
A new sustainable direct solid-state recycling of Co-Cr-Mo-W LPBF supports by mechanical milling
2026 · Temel Varol, Hüseyin Can Aksa, et al. · Powder Technology · 2
The role of enhanced process parameters on surface, microstructure, physical and mechanical properties of AlSi10Mg alloys manufactured by laser powder bed fusion
2025 · Murat Beder, Temel Varol, et al. · Materials Today Communications · 2
Taguchi optimization of electrolytic Cu powders recycled from scrap Cu plates and properties of recycled Cu compacts processed by hot-pressing
2026 · Mücahit Kocaman, Temel Varol, et al. · Journal of Materials Research and Technology · 1
EFFECT OF COLD SPRAYING PARAMETERS ON THE DEPOSITION PERFORMANCE OF ADDITIVELY MANUFACTURED Ti6Al4V ALLOY
2025 · Doğukan Kolcu, Dursun Meriç, et al. · The International Journal of Materials and Engineering Technology · 1
PDF
Production and Characterization of Al2024/SiC Composites with High SiC Reinforcement
2022 · Serhatcan Berk AKÇAY, Temel VAROL, et al. · Afyon Kocatepe University Journal of Sciences and Engineering · 1
PDF
Katmanlı Parçacıklar Kullanılarak Üretilen Bakır Esaslı Malzemelerin Karakterizasyonu
2020 · Temel VAROL, Hüseyin Can AKSA, et al. · Karadeniz Fen Bilimleri Dergisi · 1
PDF
Morphological, mechanical and electrical evolution of copper-coated SiC reinforced Cu matrix composites manufactured by mechanical milling and hot pressing-assisted flake powder metallurgy
2026 · Mücahit Kocaman, Hamdullah Çuvalcı, et al. · Ceramics International
The effect of heat treatment on microstructural, mechanical and tribological properties of Ti-Ag alloy produced by selective laser melting method
2026 · Serhatcan Berk Akçay, Temel Varol, et al. · Scientific Reports
PDF
Processability window and defect map for LPBF of AA2024: limits of volumetric energy density
2026 · Temel Varol, Hüseyin Can Aksa, et al. · Progress in Additive Manufacturing
Production of a Personalized Orbital Reconstruction Prosthesis from CT Images Using the Powder Bed Fusion Process Method
2025 · Huseyin Can Aksa, Altug Usun, et al. · Springer tracts in additive manufacturing
Yüksek Al2O3 Oranları ile Takviye Edilmiş Al-Cu-Mg Alaşımlarının Sıcak Pres Yöntemi ile Üretimi
2023 · Serhatcan Berk AKÇAY, Temel VAROL, et al. · Düzce Üniversitesi Bilim ve Teknoloji Dergisi
PDF
Sıcak Presleme Yöntemi ile Üretilen Cu-Cr Alaşımlarının Sertlik ve Elektriksel İletkenlik Özellikleri Üzerine Mekanik Alaşımlama Süresinin Etkisi
2022 · Hamza Çolak, Serhatcan Berk Akçay, et al. · Karaelmas Science and Engineering Journal
Works count: 21
Citation count: 225
H-index: 6
I10-index: 5
Year
Topic
Type