Get started
Author

Reza Vafaei

Observed names: R. Vafaei, Reza Shoja Razavi, Vafaei, R., Vafaei, Reza
ORCID: 0009-0008-2744-6455
Observed ORCID: 0009-0008-2744-6455
OpenAlex ID: A5091816110
A novel cryogenic treatment for reduction of residual stresses in 2024 aluminum alloy
2017 · M. Araghchi, H. Mansouri, et al. · Materials Science and Engineering A · 122
Pulsed laser-assisted machining of Inconel 718 superalloy
2016 · Soheila Azhdari Tadavani, Reza Shoja Razavi, et al. · Optics & Laser Technology · 109
Evaluation of mechanical behavior of nano-grained 2024 Al alloy during high pressure torsion (HPT) process at various temperatures
2012 · R. Vafaei, M.R. Toroghinejad, et al. · Materials Science and Engineering A · 54
Improvement of MoSi2 oxidation resistance via boron addition: Fabrication of MoB/MoSi2 composite by mechanical alloying and subsequent reactive sintering
2014 · P.R. Taleghani, S.R. Bakhshi, et al. · Powder Technology · 49
Statistical-experimental modeling of the effect of process parameters on geometric characteristics of laser cladding of stellite 6 on SS316 using second-order regression
2023 · Sayed Hamid Hashemi, Reza Vafaei, et al. · Journal of Materials Research and Technology · 40
Hot compression deformation behavior of AISI 321 austenitic stainless steel
2013 · Mehdi Haj, Hojjatollah Mansouri, et al. · International Journal of Minerals Metallurgy and Materials · 36
Influence of cryogenic thermal treatment on mechanical properties of an Al–Cu–Mg alloy
2017 · M. Araghchi, H. Mansouri, et al. · Materials Science and Technology · 34
Optimization of the Mechanical Properties and Residual Stresses in 2024 Aluminum Alloy Through Heat Treatment
2018 · M. Araghchi, H. Mansouri, et al. · Journal of Materials Engineering and Performance · 26
Effects of annealing and cold rolling on microstructural features, magnetic properties, tensile behavior and electrical resistance of FeCoNi(MnAl)x high entropy alloys
2024 · Afagh Akbari, Reza Vafaei, et al. · Intermetallics · 19
Hot Deformation Behavior and Constitutive Modelling of a Medium-Carbon Structural Steel
2021 · Khalil Boroumand, Morteza Hadi, et al. · The Physics of Metals and Metallography · 11
Modeling Deformation Flow Curves and Dynamic Recrystallization of BA-160 Steel During Hot Compression
2018 · Babak Shahriari, Reza Vafaei, et al. · Metals and Materials International · 11
Aging behavior of a copper-bearing high-strength low-carbon steel
2018 · Babak Shahriari, Reza Vafaei, et al. · International Journal of Minerals Metallurgy and Materials · 10
Mechanical Properties, Microstructural Evolution, and the Effect of Friction on the Plastic Flow of the AISI 321 Austenitic Stainless Steel Tube During Cold Pilgering: An Experimental and Simulation Analysis
2018 · Mohamad Hosein Musazadeh, Reza Vafaei, et al. · Metallurgical and Materials Transactions B · 9
Continuous cooling transformation behavior and the kinetics of bainite formation in a bainitic–martensitic steel
2017 · Babak Shahriari, Reza Vafaei, et al. · International Journal of Materials Research (formerly Zeitschrift fuer Metallkunde) · 9
Nd:YAG Pulsed Laser Assisted Machining of AMS 5708 Waspaloy Alloy
2018 · Zahra Sharifi, Reza Shoja-Razavi, et al. · Lasers in Manufacturing and Materials Processing · 5
The effect of amorphous Si3N4 nanoparticles and magnetized distilled water on the mechanical properties and infrared transmittance of α-Al2O3
2025 · Mahdi Darabi, Ehsan Mohammad Sharifi, et al. · Scientific Reports · 4
Effect of amorphous Si3N4 nanoparticles, dispersing agents and magnetized water on the mechanical properties of α-Al2O3
2025 · Mahdi Darabi, Ehsan Mohammad Sharifi, et al. · Optical and Quantum Electronics · 3
An Experimentally Validated Computational Model of Damage Buildup in the Pilgering of AISI 321 Steel: Influence of Process Parameters
2020 · M. H. Musazadeh, E. Mohammad Sharifi, et al. · Transactions of the Indian Institute of Metals · 2
RETRACTED ARTICLE: Experimental and Numerical Investigation of VMR and HPTR Pilgering of Zr–1.5%Nb Tubes
2019 · M. H. Musazadeh, E. Mohammad Sharifi, et al. · Metals and Materials International · 2
Engineering colloidal homogeneity for Grain-Growth restriction in transparent Al2O3–Si3N4 nanocomposites
2026 · Mahdi Darabi, Ehsan Mohammad Sharifi, et al. · Materials & Design
Determining of essential parameter on S.S 410 during cold drawing tube process
2026 · Mohammad Mehdi Niazi, Ehsan Mohammad Sharifi, et al. · International Journal of Materials and Product Technology
Developing the Microstructure and Mechanical Characteristics of 410 Martensitic Stainless Steel During Cold Drawing of Pipes
2025 · M. M. Niazi, R. Vafaei, et al. · Metal Science and Heat Treatment
Developing the microstructure and mechanical characteristics of 410 martensitic stainless steel during cold drawing of pipes
2025 · Mohmmad mehdi Niazi, Reza Vafaei, et al. · Металловедение и термическая обработка металлов
PDF
"Multiphysics Simulation and Experimental Analysis of Laser-Clad Stellite 6 on 316 Stainless Steel Using Fem and Rsm"
2025 · sayed hamid hashemi, Reza Shoja Razavi, et al. · Research Square
PDF
Determining of essential parameter on S.S 410 during cold drawing tube process
2025 · Mohammad Mehdi Niazi, Ehsan Mohammad Sharifi, et al. · International Journal of Materials and Product Technology
Works count: 90
Citation count: 555
H-index: 11
I10-index: 12
Year
Topic
Type