Get started
Author

Ming Lv

Effect of laser remelting on deposition quality, residual stress, microstructure, and mechanical property of selective laser melting processed Ti-5Al-2.5Sn alloy
2019 · Kaiwen Wei, Ming Lv, et al. · Materials Characterization · 151
Spatially Resolved Polarization Manipulation of Ferroelectricity in Twisted hBN
2022 · Ming Lv, Xinzuo Sun, et al. · Advanced Materials · 46
Effects of laser surface modification on the adhesion strength and fracture mechanism of electroless-plated coatings
2021 · Liexin Wu, Li Meng, et al. · Surface and Coatings Technology · 35
Tailoring the surface wettability of polyimide by UV laser direct texturing in different gas atmospheres
2016 · Qifeng Du, Jianguo Liu, et al. · Materials & Design · 34
Ferroelectricity with concomitant Coulomb screening in van der Waals heterostructures
2025 · Ruirui Niu, Zhuoxian Li, et al. · Nature Nanotechnology · 30
High-adhesion Cu patterns fabricated by nanosecond laser modification and electroless copper plating
2015 · Ming Lv, Jianguo Liu, et al. · Applied Surface Science · 29
Adaptive compressed sensing algorithm for terahertz spectral image reconstruction based on residual learning
2022 · Yuying Jiang, Guangming Li, et al. · Spectrochimica Acta Part A Molecular and Biomolecular Spectroscopy · 28
Higher-resolution selective metallization on alumina substrate by laser direct writing and electroless plating
2016 · Ming Lv, Jianguo Liu, et al. · Applied Surface Science · 28
Effect of ultrasonic cavitation micro-jet impact on corrosion of material in ultrasonic assisted electrochemical micromachining
2023 · Minghuan Wang, Ming Lv, et al. · Journal of Applied Electrochemistry · 24
Fabrication of polyetheretherketone (PEEK)-based 3D electronics with fine resolution by a hydrophobic treatment assisted hybrid additive manufacturing method
2023 · Liexin Wu, Li Meng, et al. · International Journal of Extreme Manufacturing · 22
PDF
Focused laser lithographic system for efficient and cross-scale fabrication of large-area and 3D micro-patterns
2018 · Jun Ai, Ming Lv, et al. · Optics and Lasers in Engineering · 18
Cu patterns with high adhesion strength and fine resolution directly fabricated on ceramic boards by ultrafast laser modification assisted metallization
2022 · Liexin Wu, Li Meng, et al. · Surface and Coatings Technology · 16
Interference correction for laser-induced breakdown spectroscopy using a deconvolution algorithm
2020 · Kun Liu, Ran Zhou, et al. · Journal of Analytical Atomic Spectrometry · 16
THz spectrum processing method based on optimal wavelet selection
2024 · Hongyi Ge, Zhenyu Sun, et al. · Optics Express · 12
Surface modification of bisphenol A polycarbonate using an ultraviolet laser with high-speed, direct-writing technology
2014 · Ming Jiang, JianGuo Liu, et al. · Surface and Coatings Technology · 10
Surface modification of bisphenol A polycarbonate material by ultraviolet Nd:YVO4laser high-speed microprocessing technology
2014 · Jianguo Liu, Suhuan Wang, et al. · Journal of Micromechanics and Microengineering · 6
A low-cost, high-efficiency and high-flexibility surface modification technology for a black bisphenol A polycarbonate board
2014 · Suhuan Wang, Jianguo Liu, et al. · Applied Surface Science · 5
Research of Method for Tracking High Speed and Highly Maneuvering Target
2006 · Yi Ling, Lv Ming · International Conference on ITS Telecommunications · 3
Geometric algebra in electronics and information engineering: An introduction
2016 · Lin Zou, Joan Lasenby, et al. · International Journal of Electrical Engineering Education · 2
Improved OFDM channel estimation based on transform domain de-noising
2013 · Yuchao Cui, Ming Lv · IEEE International Conference on Electronics Information and Emergency Communication · 2
Tracking of High Speed and High Maneuvering Target Based on IMM Algorithm
2006 · Ming Lv · Radar Science and Technology · 2
Study of micro-bulges texture preparation in ultrasonic rolling pulse electrochemical micromachining
2023 · Minghuan Wang, Wenjun Liu, et al. · The International Journal of Advanced Manufacturing Technology · 1
An Investigation on Machining General Size Cylindrical Parts Using WEDM with Contour Approximation Method
2021 · Huliang Ma, Yanqing Wang, et al. · Research Square · 1
PDF
A predictive framework for superhydrophobic aluminum alloys based on micro-geometric mapping and a two-state composite wetting mechanism
2026 · Chuang Liu, Jimeng Zhang, et al. · Materials & Design
Sliding ferroelectric tunneling junctions with large electroresistance ratio
2026 · Xinyu 新裕 Lv 吕, Ming 铭 Lv 吕, et al. · Chinese Physics B
Works count: 31
Citation count: 521
H-index: 13
I10-index: 15
Year
Topic
Type