Get started
Author

Bülent Öztürk

Observed names: B Öztürk, B. Öztürk
Observed institution: Karadeniz Technical University
ORCID: 0000-0002-8836-572X
Observed ORCID: 0000-0002-8836-572X
OpenAlex ID: A5101531614
Effects of Different Kinds of Fibers on Mechanical and Tribological Properties of Brake Friction Materials
2013 · Bülent Öztürk, Fazli Arslan, et al. · Tribology Transactions · 104
Hot wear properties of ceramic and basalt fiber reinforced hybrid friction materials
2006 · Bülent Öztürk, Fazlı Arslan, et al. · Tribology International · 104
Effects of Resin Type and Fiber Length on the Mechanical and Tribological Properties of Brake Friction Materials
2011 · Bülent Öztürk, Sultan Öztürk · Tribology Letters · 100
Effect of Type and Relative Amount of Solid Lubricants and Abrasives on the Tribological Properties of Brake Friction Materials
2013 · B. Öztürk, S. Öztürk, et al. · Tribology Transactions · 51
Hybrid effect in the mechanical properties of jute/rockwool hybrid fibres reinforced phenol formaldehyde composites
2010 · Bülent Öztürk · Fibers and Polymers · 50
Experimental investigation of the melting performance of a low porosity metal foam/PCM composite heat sink in various configurations
2023 · Bülent Öztürk, Zafer Gölbaşı, et al. · International Communications in Heat and Mass Transfer · 43
Effects of Zinc Borate and Fly Ash on the Mechanical and Tribological Characteristics of Brake Friction Materials
2015 · B. Öztürk, T. Mutlu · Tribology Transactions · 41
Oxidation, electrical and mechanical properties of Crofer ® 22 solid oxide fuel cell metallic interconnects manufactured through powder metallurgy
2018 · Bülent Öztürk, Alparslan Topcu, et al. · International Journal of Hydrogen Energy · 37
The structural and mechanical properties of open-cell aluminum foams: Dependency on porosity, pore size, and ceramic particle addition
2024 · Zafer Gölbaşı, Bülent Öztürk, et al. · Journal of Alloys and Compounds · 29
Performance evaluation of machined and powder metallurgically fabricated Crofer®22 APU interconnects for SOFC applications
2021 · Alparslan Topcu, Bülent Öztürk, et al. · International Journal of Hydrogen Energy · 29
Erosive wear characteristics of E‐glass fiber reinforced silica fume and zinc oxide‐filled epoxy resin composites
2019 · Bülent Öztürk, Hasan Gedikli, et al. · Polymer Composites · 29
Mechanical, wear and corrosion behavior of Ti–6Al–xNb (x = 3.5–21 wt%) alloys manufactured by powder metallurgy
2023 · Zafer Gölbaşı, Bülent Öztürk, et al. · Powder Technology · 20
Influence of processing parameters on the porosity, thermal expansion, and oxidation behavior of consolidated Fe22Cr stainless steel powder
2020 · Bülent Öztürk, Alparslan Topcu, et al. · Powder Technology · 16
Improvement of solid particle erosion resistance of helicopter rotor blade with hybrid composite shield
2020 · İsmail Özen, Hasan Gedikli, et al. · Engineering Failure Analysis · 14
Effect of Sn addition on mechanical, wear, and electrochemical properties of Ti-Al-Sn alloys
2024 · Zafer Gölbaşı, Bülent Öztürk, et al. · Powder Technology · 12
Exploring the role of Fe in the wear and corrosion resistance of Ti-based alloys produced with conventional powder metallurgy
2024 · Zafer Gölbaşı, Kürşat Için, et al. · Tribology International · 10
The Role of Wheel Surface Quality on Structural and Hard Magnetic Properties of Nd–Fe–B Permanent Magnet Powders
2018 · Sultan Öztürk, Kürşat İcin, et al. · Journal of Superconductivity and Novel Magnetism · 8
Effect of production parameters on cooling rates of AA2014 alloy powders produced by water jet cooled, rotating disc atomisation
2003 · S. Öztürk, F. Arslan, et al. · Powder Metallurgy · 8
Enhanced Magnetic Properties of Nd15Fe77B8 Alloy Powders Produced by Melt-Spinning Technique
2017 · Sultan Öztürk, Kürşat İcin, et al. · Metallurgical and Materials Transactions A · 7
Effect of process parameters on production of metal powders by water jet cooled rotating disc atomisation
2005 · S. Öztürk, F. Arslan, et al. · Powder Metallurgy · 7
Investigation of milling characteristics of alumina powders milled with a newly designed vibratory horizontal attritor
2004 · Yusuf Kilinç, Sultan Öztürk, et al. · Powder Technology · 7
Characteristics of rapidly solidified Cu–10%Sn alloy powders produced by water jet cooled rotating disc atomisation
2011 · S Öztürk, B Öztürk, et al. · Powder Metallurgy · 5
Production of rapidly solidified Cu–Sn ribbons by water jet cooled rotating disc method
2011 · Sultan Öztürk, Bülent Öztürk, et al. · Journal of Materials Processing Technology · 5
Investigation on Solid Particle Erosion Performance of Aluminum Alloy Materials for Leading-Edge Slat
2024 · Ali İhsan Budur, İsmail Özen, et al. · Tribology in Industry · 3
PDF
Aşındırıcı Türü ve Boyutunun Otomotiv Fren Balatalarının Sürtünme-Aşınma Performansına Etkisi
2018 · Bülent Öztürk · Gümüşhane Üniversitesi Fen Bilimleri Enstitüsü Dergisi · 3
PDF
Works count: 34
Citation count: 743
H-index: 14
I10-index: 16
Year
Topic
Type