Author

С. Бен Салем

Observed names: S. B. Salem, S. Ben Salem, Sarra Ben Salem

Institutions: Tunis University, National Engineering School of Tunis, Tunis El Manar University

Observed institutions: Tunis University, University of Carthage, University of Guelma, National Engineering School of Tunis, ENSIT, Tunis El Manar University

OpenAlex ID: A5109183367

Influence of machining parameters on the surface integrity in electrical discharge machining

2009 · M. Boujelbene, E. Bayraktar, et al. · Archives of Materials Science and Engineering · 76

Effect of the cutting speed on the chip morphology and the cutting forces

2009 · A. Daymi, M. Boujelbene, et al. · Archives of Materials Science and Engineering · 28

Optimization of the surface roughness in ball end milling of titanium alloy Ti-6Al-4V using the Taguchi Method

2018 · W. Mersni, M. Boujelbene, et al. · Procedia Manufacturing · 25

Influence of TiO2 on the Microstructure, Mechanical Properties and Corrosion Resistance of Hydroxyapatite HaP + TiO2 Nanocomposites Deposited Using Spray Pyrolysis

2023 · Hafedh Dhiflaoui, Sarra Ben Salem, et al. · Coatings · 23

Investigation of cut edge microstructure and surface roughness obtained by laser cutting of titanium alloy Ti-6Al-4V

2021 · B. El Aoud, M. Boujelbene, et al. · Materials Today Proceedings · 17

Experimental Modeling and Multi-Response Optimization in Friction Stir Welding Process Parameters of AA2024-T3 Using Response Surface Methodology and Desirability Approach

2024 · K. Boulahem, S. B. Salem, et al. · Experimental Techniques · 13

Optimization of Kerf Quality During CO2 Laser Cutting of Titanium Alloy Sheet Ti-6Al-4V and Pure Titanium Ti

2018 · B. El Aoud, M. Boujelbene, et al. · Conference proceedings of the Society for Experimental Mechanics · 13

A Comparative Study on the Effect of Milling and Abrasive Water Jet Cutting Technologies on the Tensile Behavior of Composite Carbon/Epoxy Laminates

2021 · A. Abidi, S. Ben Salem, et al. · Mechanics of Composite Materials · 12

Studying Effect of CO2 Laser Cutting Parameters of Titanium Alloy on Heat Affected Zone and Kerf Width Using the Taguchi Method

2017 · B. El Aoud, M. Boujelbene, et al. · Conference proceedings of the Society for Experimental Mechanics · 11

Experimental Comparison of the Microstructure and Surface Roughness in CO2 Laser Cutting of the Titanium Alloy Ti–6Al–4V and the Pure Titanium Ti

2018 · B. El Aoud, M. Boujelbene, et al. · Conference proceedings of the Society for Experimental Mechanics · 3

Optimization of Surface Integrity of Titanium-Aluminum Intermetallic Composite Machined by Wire EDM

2018 · S. Ezeddini, E. Bayraktar, et al. · Conference proceedings of the Society for Experimental Mechanics · 2

Mathematical Modeling of Surface Roughness in Electrical Discharge Machining Process Using Taguchi Method

2017 · A. Medfai, M. Boujelbene, et al. · Lecture notes in mechanical engineering · 2

Сравнительное изучение влияния технологий фрезерования и резки гидроабразивной струей на поведение эпоксидных слоистых углепластиков при растяжении

2021 · А. Абиди, С. Бен Салем, et al. · Механика композитных материалов

Process Reliability of Abrasive Water Jet to Cut Shapes of the Titanium Alloy Ti-6Al-4V

2018 · M. Douiri, M. Boujelbene, et al. · Conference proceedings of the Society for Experimental Mechanics

Works count: 14

Citation count: 225

H-index: 9

I10-index: 9