Source

Strojarstvo : časopis za teoriju i praksu u strojarstvu

ISSN: 0562-1887

Source type: journal

Publisher:

Alternate name: Strojarstvo

Fully OA: No

DOAJ: No

OpenAlex ID: S4306530969

Experimental Study of Surface Topography Created by Abrasive Waterjet Cutting

2007 · Sergej Hloch, Ján Valíček, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 33

Choosing the Optimal Approach to Define the Methodology of a Tariff System for Thermal Energy Activities

2007 · Eraldo Banovac, Željko Bogdan, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 10

Uniformity of Atmospheric Boundary Layer Model in the Wind Tunnel

2005 · Hrvoje Kozmar, Ivo Džijan, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 9

Thermal Comfort Models

2009 · Igor Wolf · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 7

Towards a Strategy for Mapping of Design Problems to Suitable Solutions – a Case of Design Automation Using Cbr

2006 · Mikael Cederfeldt · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 7

Validation of Francis Turbine CFD Simulations

2008 · Zoran Čarija, Zoran Mrša, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 6

Application of mathematical modelling to hardenability testing of low-alloyed Mn-Mo steel

2005 · Mirko Gojić, Ladislav Lazić, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 6

Derivation of natural gas isentropic exponent from AGA-8 equation of state

1997 · Ivan Marić · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 6

A review of internal combustion engine thermodynamic analysis using the second law of thermodynamics

2008 · Maro Jelić, Neven Ninić · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 5

Expert System for Diagnosis and Optimization of Marine Diesel Engines

2008 · Gojmir Radica · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 5

Experimental setup for SI-engine modeling and control research

2004 · Joško Petrić, Joško Deur, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 5

Control of Rotary Crane by a Combined Profile of Speeds

2009 · Nenad Blažičević, Branko Novaković · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 4

Agro-ecological and Land Information System

1999 · Mladen Jurišić, Tomislav Hengl, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 4

Applied Lean System in Process Industry

2010 · Nedeljko Štefanić, Nataša Tošanović, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 3

Analysis of Heat Transfer in Ship's Cargo Tanks

2007 · Bojan Jandrijević, Tomislav Mrakovčić, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 3

Three-dimensional Numerical Simulation of the Nitrogen Oxides Formation in an Oil-fired Furnace

2007 · Milan Vujanović, Neven Duić, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 3

CFD as an Engineering Tool for Design and Analysis

2006 · Andreja Werner, Nastia Degiuli, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 3

Suitability Evaluation of Forwarders based on morphological analysis

2004 · Dubravko Horvat, Tomislav Poršinsky, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 3

Determining the difference between estimated and realised measurement uncertainty based on comparative measurements

2004 · Vedran Mudronja, Sanjin Mahović, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 3

Heat transfer analysis in dry rotary heat exchanger

1993 · Bernard Franković · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 3

Optimization of waste heat utilization in pipeline compressor station

2009 · Davor Bišćan, Dražen Lončar · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 2

Analysis of overall SC power plant efficiency

2007 · Sandro Nižetić, Neven Ninić · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 2

Computational approach to evaluation of the flow characteristics in plate heat exchangers

2007 · Damir Dović, Srećko Švaić · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 2

PIXE spectroscopy for the analysis of cultural heritage objects

2007 · Vladan Desnica, Stjepko Fazinić, et al. · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 2

Bibliometric characteristics of the journal Strojarstvo in the Period 1992-2001

2004 · Tamara Krajna, Jelka Petrak · Strojarstvo : časopis za teoriju i praksu u strojarstvu · 2

Works count: 290

Citation count: 167

H-index: 6

I10-index: 2

2yr mean citedness: