Work

Shape‐Memory Effect in Polymers

Year: 2013
Type: article
Abstract: In recent years substantial progress has been achieved in the synthesis1 and characterization2 of shape-memory polymers (SMPs). SMPs can be programmed by a temporary fixation of a deformation, which is recovered once a suitable stimulus is applied. In most cases, the stimulus is heat, but other stimuli, such as electric current, humidity, light or alternating magnetic fields, for inducing the shape-memory effect in polymers, have been realized. Important achievements are remotely controlled actuation and the realization of more-complex movements on demand. This special issue highlights the shape-memory effect in polymers. One major request for SMPs is a broader variety of possible stimuli to adjust the shape change towards specific applications. Light as possible additional stimulus has been addressed by White et al., who explored azobenzene-functionalized polyimide materials, which are capable of a shape-change effect due to a photochemical mechanism referred to as trans-cis-trans reorientation.3 Pre-straining leads to the alignment of both the imide units as well as the azobenzene chromophores. The magnitude of the photogenerated stress can be doubled by pre-straining the material. Xie et al. explored high-intensity focused ultrasound to trigger a shape change in a thermosensitive polymer indirectly.4 A polyurethane containing PCL as a switching segment was loaded with copper sulfate as model compound. Exposure to the focused ultrasound induced a shape recovery and changed the diffusibility of the model compound in the SMP matrix. The softening of glassy switching domains by uptake of water has been examined in SMP foams by Wilson et al.5 Decreasing the glass transition temperature (Tg) of the switching domains to a temperature lower than the environmental temperature induced the shape-memory effect. By adjusting the hydrophobicity of the SMP, the time of shape recovery in water can be controlled from 2 min to more than 24 h. The depressed Tg was increased from 12 to 40 °C by increasing the hydrophobicity of the diisocyanate monomer. A direct sensing capability has been explored by Schroeter et al. using redox-sensitive poly(p-phenylene ethynylene)s (rsPPEs) that can be reduced and oxidized in solution as well as in the solid state, accompanied by a change of photoluminescence values.6 rsPPEs with good thermal stability (up to 250 °C) and solubility in common organic solvents were achieved, while switching of the optical properties was possible by oxidation and reduction with different reagents. Furthermore, a change in conductivity caused by the redox reaction might enable, for example, electrical heating to be controlled using rsPPEs. Despite the great potential of novel stimuli, a strong interest in SMP research still lies in the improvement of thermosensitive dual-shape polymers like the enhancement of their structural shape-memory properties,7 as well as the exact placement of their switching temperature within a desired temperature range.8 In their work, Jana and Erden describe special blends of thermoplastic polyurethanes with polybenzoxazine (PB), where PB serves as a second set of netpoints supporting a permanent shape, as an alternative to the use of inorganic nanofillers.7 Such compounds were prepared in a three-step synthesis, where, at first, the benzoxazine monomer was dissolved in the urethane prepolymer; next, the prepolymer was chain-extended with 1,4-butanediol; and, finally, the benzoxazine was polymerized into PB by thermal curing within the polyurethane matrix. As compared with inorganic nanofillers, PB can be directly coupled by copolymerization or grafting reactions, in addition to simply blending both polymers, while PB represents an additional hard phase due to the high Tg of the related domains, and therefore causes a much greater storage modulus. The results showed a strong increase in the Young's modulus and the ultimate stress at ambient temperature. Furthermore, the shape-memory properties of the blends were substantially improved with respect to the shape fixity and shape recovery, as well as the recovery stress, compared with pure polyurethane. Interestingly, even though strong changes in the mechanical properties were achieved, the maximum amount of PB was only 17 wt%. In another approach, which was followed by Dong and Weiss, the creation of blends from fatty acids and elastomeric ionomers not only resulted in high shape fixation and shape-recovery ratios of almost 100%, but the switching temperature could also be accurately adjusted within a desired temperature range from 20 to 120 °C.8 However, the SMP system showed, so far, significant time-dependent relaxation both in the temporary and the permanent shape, which is thought to origin from creep. To address this question the authors identified the ionic network to be the weak link in the stability of the shape and that by covalent crosslinking of the ionomer, the problem of creep could be resolved. Different-shaped bodies from SMP and applications are addressed within this special issue such as foams,5, 9 fiber-reinforced composites,10 and neurovascular stents.11 Porous shape-memory polymers offer large recovery strains upon compaction (e.g., in foams), but the shape change of small micropores can be utilized for filtration purposes as well. Additionally, by introducing micrometer-sized pores into the SMP, a porous system is obtained with a new hierarchical structure on the microscale, which influences the shape-memory properties. While the foam density has a minor influence on the shape recovery, but a profound influence on the stress recovery of SMP foams, a work presented by Sauter et al. describes the influence of the pore-size distribution on the shape-memory properties.9 The bimodal hierarchical pore-size distribution increased the shape-recovery ratio of the foam drastically, as compared with a homogeneous monomodal pore-size distribution, even though the foam density of both foams was identical. The pore analysis revealed microscale bending of the large pore walls in the hierarchical foams that stored more elastic (or recoverable) energy than microscale buckling in the homogeneous foam, which was confirmed by S-shaped pore walls, indicating failure of the structural unit. The recovery stress only mildly differed between the two foam types. While foams offer a microstructural architecture to tailor the overall shape-memory properties, reinforced composite materials can be used to direct the shape-memory effect. Anisotropic mechanical properties due to fiber orientation was subject of a study performed by Mather et al.10 The aim was to create soft anisotropic SMPs that mimic a bat wing by incorporating aligned poly(vinyl acetate) fibers into an elastomeric matrix. After fiber infiltration, the matrix was cured and a shape-memory capability was obtained by a strain-fixing thermoplastic fiber phase and recovery through the elastomeric silicone matrix. Very interestingly, the shape-fixity was gradually reduced with increasing deviation from the longitudinal fiber orientation, which was expected since the fibers are responsible for maintaining the temporary shape. Furthermore, good shape-recovery properties were obtained and a change in Young's modulus of the bat wing, depending on the loading direction, could be matched by the composite. Maitland et al. suggest a neurovascular stent as a potential product based on SMPs and introduce demonstrator devices prepared by dip-coating of thermoplastic polyurethane made from butenediols and trimethylhexamethylene diisocyanate combined with a radiation sensitizer (pentaerythritol triacrylate) onto a rod, laser cutting, and electron-beam irradiation.11 The crosslink density was controlled by varying the electron beam dose, radiation-sensitizer concentration, CC composition, or molecular weight of the thermoplastic polymer. Besides SMP technology, another approach based on the principle of metallic bilayers (active and passive component) was followed by Ionov for polymeric systems, where the self-folding capability of bilayer polymer films is set in relation to the natural mechanisms of plant motion.12 Two approaches are presented to design self-folding films, the formation of bilayers that are able to produce rather simple geometries, such as tubes or capsules, and complexly patterned films with locally deposited active materials, which can form objects with sharp edges, such as cubes and pyramids. Self-folding films thus consist of two materials, where, in the simplest case, one is an active stimuli-responsive (e.g., hydrophilic hydrogel) polymer and the other is passive (e.g., hydrophobic). In such a case, folding and unfolding is a reversible process that depends on the application of water as a stimulus. The shape-memory behavior of poly(L-lactide) (PLLA) was simulated using a molecular dynamics approach aimed at a knowledge-based approach for SMPs.13 The complete thermomechanical cycle of programming, unloading, and recovery was described on the atomistic level for uniaxial stretching experiments. Two different stretching methods were applied: the direct stretching approach, in which an external stress tensor is imposed, and geometrical stretching, where the volume of the packing box is kept constant (elongation in one direction leads to contraction in the other two directions). The simulation revealed a high shape-fixity ratio of above 90%, while moderate shape-recovery ratios with 30–48% were obtained independent of the applied stretching method, which was comparable to the experimental results of PLLA. In summary, the articles presented in this special issue highlight the rapid advancement in the SMP development. The issue covers a broad range, from the theoretical description of the shape-memory effect in polymers, up to application-oriented research. Fundamental work on novel stimuli as well as major advances of thermosensitive dual-shape polymers is presented. We thank all of the authors for their interesting and stimulating contributions. Furthermore, we gratefully acknowledge Dr. Stefan Spiegel from Wiley-VCH, Dr. Karolin Schmälzlin, and Sabine Benner, both from HZG, for their valuable editorial and administrative support.
Language: English
Open Access status: bronze
OpenAlex ID: W1976081677
FWCI: 6.837
Cites: 3
Cited by: 42
Related to: 10