Work

Nanostructured Particulate and Fibrous Materials for Fuel Cell Electrode Application

Year: 2015
Type: dissertation
Abstract: The objective of this thesis is to systematically investigate the synthesis of nanostructured particle and fibrous materials using spray process (i.e.spray pyrolysis and electrospray) and their application.Various types of nanostructured particles such as dense, hollow and porous particles and nanofiber have been developed and their application as catalyst was examined subsequently.The structural properties and electrocatalytic activity of the prepared nanostructured catalyst materials are reported thoroughly.Chapter 1 describes the background, previous research, objectives and outline of thesis.Chapter 2 describes the synthesis and evaluation of porous carbon derived from phenolic resin using a fast and facile spray pyrolysis method has been studied for use as a new electrocatalyst support material.By adding polystyrene latex nanoparticles as a template to the phenolic resin precursor, self-organized macroporous carbon structure was first developed.The mass ratio of phenolic resin to PSL at 0.625 gave the optimum porous morphology.Pt nanoparticles (∼20 wt %) were grown on the carbon surface using a standard industrial impregnation method.Well-dispersed Pt nanoparticles of average size 3.91 nm were observed on the surface of porous carbon particles.The high catalytic performance of porous Pt/C electrocatalyst was confirmed by the high mass activity and electrochemically active surface area, which were 450.81 mA mg -1 -Pt and 81.78 m 2 g -1 -Pt, respectively.The porous Pt/C catalyst obtains two times higher mass activity than that of the commercial Pt/C catalyst and performs Abstract iii excellent durability under acid conditions.Chapter 3 describes that the synthesis of nanostructured carbon particle is challenging because of the poor ability of polymeric precursors to self-assemble during spray pyrolysis.Here, we report a facile method for designing self-organized nanostructured carbon particles.A dual polymer system of phenolic resin and electrically charged polystyrene latex is ultrasonically spray pyrolyzed to produce either hollow or porous carbon particles.The hollow and porous carbon particles exhibit high CO 2 adsorption capacities of 3.0 and 4.8 mmol g -1 , respectively.Chapter 4 describes the synthesis of Pt/SnO 2 nanofibers via electrospinning.The unique electrochemical properties were in evidence based on the activity that allowed a hydrogen oxidation reaction and inhibit an oxygen reduction reaction.A high electrochemically active surface area value of 81.17 m 2 /g-Pt was achieved with ultra-low Pt loading (4.03 wt.%).The kinetics of a hydrogen oxidation reaction was investigated using a linear sweep voltammetry technique under a hydrogen atmosphere.A diffusion-limited current was achieved at 0.07 V and was stable at a high potential.This preparation technique shows great promise for the design of anode electrocatalyst material for fuel cells.Chapter 5 describes a facile method to synthesize Pt nanoparticles on the electrospun SnO 2 fiber matrix is presented.Precursors contained tin chloride pentahydrate, hexachloroplatinic acid, polyacrylonitrile, and N,N-dimethylformamide was electrospun subsequent calcination at 500 o C for 4 h.It is shown that Pt nanoparticles were grown on SnO 2 fiber matrix without any formation of PtO.Pt nanoparticles size was span in the range of 6-32 nm, by adjusting the concentration of Abstract iv polyacrylonitrile.The electrochemically active surface area of Pt/SnO 2 fibers was found very competitive to the commercially available electrocatalyst.This work demonstrates that Pt/SnO 2 fibers can be generated by a facile electrospinning process.The conclusion of this thesis is mentioned in Chapter 6.
Language: English
Field: Energy
Open Access status: green
OpenAlex ID: W2116724574
Cites: 75
Cited by:
Related to: 9