Synthesis and Study of Carbon Nanotubes and Carbon Spheres
Year: 2009
Type: dissertation
Abstract: ABSTRACT \nThe synthesis of multi-walled carbon nanotubes (MWCNTs) and carbon spheres (CSs) \nwas achieved using catalytic and non-catalytic chemical vapour deposition processes \n(CVD) respectively. Fe-Co bimetallic catalysts supported on CaCO3 were prepared by a \nwet impregnation (IMP), a deposition-precipitation (DP) and a reverse micelle method \n(RM). The sizes of the Fe and Co particles were not affected by the Fe and Co sources \n(nitrate, acetate) when the wet impregnation and deposition-precipitation methods were \nused. High quality ‘clean’ multi-walled carbon nanotubes (MWCNTs) were obtained \nfrom all three Fe-Co synthesis procedures under optimized reaction conditions. The \nCNTs produced gave yields ranging from 623% - 1215% in 1 h under the optimum \nconditions, with similar outer diameters (o.d.) of 20 - 30 nm and inner diameters (i.d.) ~ \n10 nm. The Fe-Co catalyst formed in the wet impregnation method revealed that the \nyield, outer diameter and purity of the CNTs were influenced by C2H2/N2 ratios, time and \ntemperature. All the methods gave high quality CNTs after short reaction times but the \nquality deteriorated as the synthesis time was increased from 5 - 360 min. Indeed, the \ninfluential parameter in controlling CNT purity, length and outer diameter was found to \nbe the synthesis time. \nIn order to control the i.d. of the CNTs, the three methods of catalyst preparation were \nemployed with the aim of controlling the Fe-Co catalyst particle sizes. It was observed \nthat the IMP and DP methods were less effective in controlling the size of the metal \nparticles. A reverse micelle process was used to synthesize Fe-Co nanoparticles that were \nhighly crystalline and uniform in size. The reverse micelle technique displayed the ability \nto prepare nanoparticles of controlled size (3, 6 and 13 nm) obtained by varying the \nconcentrations of Fe and Co in the micelle. By using the RM method, smaller diameter \nCNTs could be obtained compared with the IMP and DP methods. The CNT i.d. was \nfound to correlate with the size of the catalyst particle used. \nThe effect of synthesis time on CNT widths was investigated for the first time. In this \nstudy the issue of carbon build up on the CNTs as a function of time was investigated. It was observed that both the CNT yield and the outer diameters increased with time. With \nincrease in synthesis time, the tubes broke into small fragments. The use of excess C2H2 \nresulted in the deposition of carbon on the already formed CNTs and it is this deposited \ncarbon that caused tube fragmentation. \nMWCNTs with unusual rough surfaces (including pits) were synthesized by the CVD of \nacetylene using a novel Ca3(PO4)2-CaCO3 support mixture. Mixtures of Ca3(PO4)2- \nCaCO3 (0/100 to 100/0) yielded tubes with very rough surfaces and the CNT yield \nincreased as the amount of CaCO3 in the support mixture was increased. The inner walls \nof the CNTs possessed a regular orientation of crystalline graphite sheets (3 - 5 nm) while \nthe outer surface of the CNTs had a thick, rough, compact layer (~ 30 nm) of carbon with \na random orientation of graphite sheets. \nThe production of pure carbon spheres (CSs) was achieved in the absence of a catalyst \nthrough the direct pyrolysis of acetylene and ethylene in a horizontal CVD reactor. The \ndetailed experiments conducted with acetylene as a precursor indicated that the diameters \nof the CSs could be controlled by varying the pyrolysis conditions (e.g. temperature and \nsynthesis time) and that the process could readily be scaled up for commercial production. This process thus provides a variant of the carbon black synthesis procedure. \nThe effect of using oxygenates (alcohol C:O ratio dependence) on the CS morphology \nwas also investigated. \nCSs were also synthesized in a vertical swirled floating catalytic chemical vapour \ndeposition (SFCCVD) reactor for the first time. This process allowed for continuous and \nlarge scale production of these materials. The CSs were obtained by the direct pyrolysis \nof acetylene in an inert atmosphere without the use of a catalyst. The effect of pyrolysis \ntemperatures and the flow rate of argon carrier gas on the size, quality and quantity of the \nsynthesized carbon spheres were investigated. TEM analysis of the carbon materials \nrevealed graphitic spheres with a smooth surface and uniform diameter that could be \ncontrolled by varying reaction conditions (size: 50 - 250 nm). The materials were spongy \nand very light. It was established that under controlled experimental parameters, sphere size is also regulated by the structural and bonding properties of a hydrocarbon source \nsuch as carbon/hydrogen (C:H) content, hybridization and isomerism.
Author: Sabelo D. Mhlanga
Language: English
Subfield: Materials Chemistry
Field: Materials Science
Domain: Physical Sciences
Open Access status: green
OpenAlex ID: W2265734408
