Work

A light-weight Malaise trap

Year: 1972
Type: article
Abstract: My lighter weight design is described below.It weights 1.2 pounds (without the jar for alcohol).Many variations of this pattern can be used, but one should not believe that innovations will be better, or even equal, until they are proven in field tests.As examples, sagging of the top of the trap lessens the catch, and the exact shape given for the top pieces of the trap is meant to minimize sagging.The color of the trap is important.I spent two months of one summer experimenting with the colors of various parts.The clack colored parts, as recommended, increase the catch 70% (in shade) to 180% (in sunlight), over the catch of an entirely white trap that is otherwise identical.There could be further improvements in the color pattern, but unless one has the time to test his experimental colors, it would be advisable to use the colors recommended.Below is a list of materials for one trap of the light weight design, followed by descriptions and illustrations of trap parts, and directions for assembly.LlST OF MATERIALS Dacron marquisette, 44 inches wide (or 41 to 46 inches wide), 25 meshes per inch; 36 feet.( Dacron is called Terylene in Great Britain. ) Cotton marquisette netting can be used but this is prone to rot in wet weather.Do not use nylon, as nylon is rotted by sunlight.Cotton twill tape, 1/2 inch wide: 98 feet.Preshrink this before use by soaking in hot water and drying without stretching.Wind it on a piece of cardboard, without stretching.Thread (preferably Dacron but cotton acceptable), 40 or 50 gauge: 200 yards.Cotton twine: about 40 feet.Plastic jar (non-linear polypropylene or non-linear polyethylene) of a mason jar design: 1 pint size, with screw cap of the same kind of plastic.The jar diameter is 3V4 inches, height 5% inches, and mouth opening 2% inches.Some other plastic jar of about the same size can be substituted.Aluminum stock, 1/8 inch thick, size 3V4x7 inches.Aluminum stock, 1/16 inch thick, size 3V4x3V4 inches.Heavy galvanized iron (3y4x3x/4 inches) can be substituted.4 machine bolts, brass, flat headed, 1/8 inch diameter, 3/8 inch long, with nuts. 4 machine bolts, brass, round headed, 1/8 inch diameter, 1/2 inch long, with nuts. 1 spray can of flat black paint, 12 ounces content.Rubber cement or contact cement.Total cost of materials is $9.00 to $20.00, depending on the retailer's profit.Tools needed: Scissors, sewing machine, about 100 straight pins, saber saw or scroll saw with blade for aluminum cutting, bench vise, drill with 1/8 inch twist bit, and another twist bit of 5/16 to 1/2 inch diameter (for countersinking), nail or scribe with sharpened point, pocket knife, hammer, large Ent.News, Vol.83, November 1972 D. Roof panel (figure 1, D); make two.Dacron marquisette, cut as in figure.Selvedge must be along the long side.Pin twill tape to the oblique side and the concave side before these cuts are made.Sew twill tape on all edges, double stitched.E. Center baffle, upper part (figure 1, E).Dacron marquisette cut as in the figure.Sew twill tape to all edges but the oblique edge, double stitched.F. Front of roof (figure 1, F).Dacron marquisette, cut as in the figure.Selvedge must be along the 4 foot side.Pin twill tape to the two sloping sides before these cuts are made.Sew twill tape on all edges, double stitched.J. Tie loops; make 14.Cut 1/2 inch twill tape into 6 inch lengths.
Language: English
Subfield: Insect Science
Open Access status: green
OpenAlex ID: W3170794598
FWCI: 2.079
Cites:
Cited by: 355
Related to: 10