Work

Experimental approaches for characterizing, understanding and predicting lignocellulosic biomass flows in valorization processes

Year: 2026
Type: conference-paper
Abstract: Increasing pressure on industries to reduce their environmental impact, together with the progressive depletion of natural resources, underscores the need for efficient biomass valorization processes. Such processes are critical for a sustainable bioeconomy but require a thorough understanding of biomass rheology during handling, transport and conversion [1,2]. Predicting and controlling the flow of solid biomass is challenging due to the inherent complexity of these materials, which combine wide particle size distributions, irregular shapes, significant elastic recovery after stress, and variable moisture content, along with extrinsic heterogeneity arising from seasonal and biological variations [1,3–6].This study investigates the influence of physical and physico-chemical properties on the flow behavior of lignocellulosic biomass, using wood sawdust as a model material. The approach focuses on (i) physical and physico-chemical characterization of the selected biomasses, (ii) rheological testing under different flow conditions, and (iii) analysis to identify the main factors governing flow behavior.Two types of lignocellulosic biomass, beech wood and fir wood, were selected and tested in three particle size ranges (fine, medium and coarse) from 50 µm to 1.5 mm. Physical characterization revealed a narrow particle size distribution but pronounced heterogeneity in particle morphology, consistent with the selection of fibrous, irregular and non-spherical particles intended to represent unconventional biomasses, such as cereal straw, commonly processed in biorefineries [7]. These geometrical features promote interlocking and entanglement, strongly affecting flow behavior. Rheological properties were characterized using complementary methods: quasi-static flow was assessed with a shear cell, while dense flow behavior was evaluated using both a powder rheometer and a rotating drum.Shear testing was performed with the RST XS.s using the XS-Mr cell, which is suitable for particles up to 1 mm. This enabled reliable measurements for the fine and medium size biomasses, but excluded the coarse biomass (~1.5 mm). Lignocellulosic powders exhibit atypical behavior: they develop strength under consolidation but become almost free-flowing once the stress is released [6]. Consequently, the standard test procedure often failed, preventing the construction of Mohr’s circles.To obtain usable data, a modified protocol was developed and applied to all selected wood sawdust. This involved a low pre-shear stress of 3 kPa and only three consolidation points, with the maximum level limited to 60% instead of the standard 80%, allowing reproducible measurement of shear behavior without overstressing the material.Rheological measurements with the FT4 powder rheometer also required adjustments to the standard protocol. The standard configuration, which uses a 50 mm vessel diameter and a 48 mm blade diameter with a clearance of 1 mm on each side, was unsuitable for the coarse biomass. The coarse wood particles, with sizes around 1.5 mm, were larger than the available gap and could not pass freely between the blade and the vessel wall. As a result, the blade became stuck or completely blocked, preventing proper conditioning of the sample. This caused poor repeatability, particle breakage, and modifications of the measured energy and flow parameters, which made the standard procedure unreliable for these materials. To define an appropriate configuration, aluminum oxide was used as a reference material with three particle sizes (13, 62, and 125 µm), covering a range from highly cohesive powders to coarser grains. Tests were conducted using both the 50 mm vessel with 48 mm blade and a modified configuration, the 62 mm vessel diameter with the same blade, providing a wider 7 mm clearance. Results from the two setups were compared and found to be consistent, showing the same tendency across all three particle sizes, confirming the validity of the modified protocol. Therefore, the 62 mm vessel paired with the 48 mm blade was chosen for FT4 rheological testing of the three biomass particle size ranges, providing a wider gap between the vessel and the blade.The Granudrum rotating drum was used to perform two tests to assess dense flow behavior. The first was a speed hysteresis test, which determines the cohesive index and angle of repose, providing a measure of the material’s flowability from free-flowing to hard-to-flow. The second was the angle of first avalanche test, which identifies the angle at which particles begin to move as the drum rotates slowly. This test gives insight into the material’s initial resistance to flow, with higher first avalanche angles indicating more cohesive powders. Together, these tests allow a comprehensive characterization of particle mobility and cohesion under dynamic conditions.Overall, the results obtained so far show that standard rheological procedures are not directly applicable to some lignocellulosic biomass, particularly for irregular, fibrous or coarse particles. The adapted shear test and FT4 protocols developed in this work were therefore essential to avoid artefacts such as particle breakage, overstressing during consolidation or misinterpretation of cohesive behavior. These adaptations represent a central objective of the study: to establish reliable testing methodologies tailored to the specific behavior of biomass, and to compare their outcomes with those obtained using conventional protocols. Moisture content was also found to have a strong impact on flowability, by increasing friction and promoting liquid bridge formation, which hinders particle movement [8] further reinforcing the need for controlled and material-specific testing conditions. Ongoing experiments using the refined protocols aim to consolidate these findings and provide robust, reproducible rheological data across the different particle sizes and moisture states of the selected wood sawdust and cereal straw.References1. Cheng Z, Leal JH, Hartford CE, Carson JW, Donohoe BS, Craig DA, et al. Flow behavior characterization of biomass Feedstocks. Powder Technology. 2021 July 1;387:156–80. 2. Hernandez-Shek MA. Développement et validation de méthodologies et d’outils opérationnels de caractérisation rhéologique de biomasses appliqués au procédé de méthanisation en voie solide, et conception de réacteurs de 0,5 m3 [Internet] [phdthesis]. Université de Technologie de Compiègne; 2020 [cited 2025 June 27]. Available from: https://theses.hal.science/tel-033514883. Barletta D, Berry RJ, Larsson SH, Lestander TA, Poletto M, Ramírez-Gómez Á. Assessment on bulk solids best practice techniques for flow characterization and storage/handling equipment design for biomass materials of different classes. Fuel Processing Technology. 2015 Oct;138:540–54. 4. Ilic D, Williams K, Farnish R, Webb E, Liu G. On the challenges facing the handling of solid biomass feedstocks. Biofuels, Bioproducts and Biorefining. 2018;12(2):187–202. 5. Research needs on biomass characterization to prevent handling problems and hazards in industry: Particulate Science and Technology: Vol 34, No 4 [Internet]. [cited 2025 June 27]. Available from: https://www.tandfonline.com/doi/abs/10.1080/02726351.2016.11382626. Schulze D. Powders and Bulk Solids: Behavior, Characterization, Storage and Flow [Internet]. Cham: Springer International Publishing; 2021 [cited 2025 June 27]. Available from: https://link.springer.com/10.1007/978-3-030-76720-47. Wang S, Ji S. Flow characteristics of nonspherical granular materials simulated with multi-superquadric elements. Particuology. 2021 Feb 1;54:25–36. 8. Suhag R, Kellil A, Razem M. Factors Influencing Food Powder Flowability. Powders. 2024 Feb 19;
Source: HAL
Language: English
Open Access status: green
OpenAlex ID: W7162383040
FWCI:
Cites:
Cited by:
Related to: 10