Author

M. M. M. Sarcar

Observed names: M M M Sarcar, M M M, Sarcar, M.M.M. Sarcar, Mohammed Moulana Mohiuddin Sarcar, Sarcar M M M

Institutions: Andhra University, Jawaharlal Nehru Technological University Anantapur

Observed institutions: Andhra University, Siddhartha Academy of Higher Education, Jawaharlal Nehru Technological University Anantapur

OpenAlex ID: A5044628552

Mechanical properties of Aluminum-Copper(p) composite metallic materials

2016 · Siddabathula Madhusudan, Mohammed Moulana Mohiuddin Sarcar, et al. · Journal of Applied Research and Technology · 89

PDF

Tribological properties of Aluminium Metal Matrix Composites (AA7075 Reinforced with Titanium Carbide (TiC) Particles)

2016 · V. Ramakoteswara Rao, N. Ramanaiah, et al. · International Journal of Advanced Science and Technology · 61

Tribological and Corrosion behavior of HVOF Sprayed WC-Co, NiCrBSi and Cr3C2-NiCr Coatings and analysis using Design of Experiments

2015 · Shabana, M.M.M. Sarcar, et al. · Materials Today Proceedings · 58

Development of a system for monitoring tool condition using acousto-optic emission signal in face turning—an experimental approach

2010 · Balla Srinivasa Prasad, M. M. M. Sarcar, et al. · The International Journal of Advanced Manufacturing Technology · 55

Fabrication and Investigation on Properties of TiC Reinforced Al7075 Metal Matrix Composites

2014 · V. Rama Koteswara Rao, N. Ramanaiah, et al. · Applied Mechanics and Materials · 33

Fabrication and characterization of aluminium–copper composites

2008 · S. Madhusudan, M.M.M. Sarcar, et al. · Journal of Alloys and Compounds · 33

Dry Sliding Wear Behavior of Tic-AA7075 Metal Matrix Composites

2015 · V. Ramakoteswara Rao, N. Ramanaiah, et al. · 31

Optimization of Wire Electric Discharge Machining Parameters for Surface Roughness on 316 L Stainless Steel Using Full Factorial Experimental Design

2014 · P. Raju, M.M.M. Sarcar, et al. · Procedia Materials Science · 31

Evaluation of Optimal Parameters for machining with Wire cut EDM Using Grey-Taguchi Method

2013 · Sriram Subrahmanyam, M. M. M. Sarcar · 29

Evaluation of optimal parameters for machining brass with wire cut EDM

2009 · Ch. V. S. Parameswara Rao, M. M. M. Sarcar · Journal of Scientific & Industrial Research · 23

Optimisation of process parameters for minimum volumetric wear rate on AA7075-TiC metal matrix composite

2017 · V. RamakoteswaraRao, N. Ramanaiah, et al. · International Journal of Automotive and Mechanical Engineering · 18

PDF

Effect of heat treatment on corrosion behavior of duplex coatings

2014 · K. Raghu Ram Mohan Reddy, N. Ramanaiah, et al. · Journal of King Saud University - Engineering Sciences · 18

PDF

Surface textural analysis using acousto optic emission- and vision-based 3D surface topography—a base for online tool condition monitoring in face turning

2011 · Balla Srinivasa Prasad, M. M. M. Sarcar, et al. · The International Journal of Advanced Manufacturing Technology · 18

Studies on photo- and thermal stability of PVA-encapsulated Mn-doped ZnS nanoparticles

2016 · Savadana Venkataramana, K. Ramanaiah, et al. · Applied Physics A · 13

Static analysis of thick skew laminated composite plate with elliptical cutout

2009 · M. S. R. Niranjan Kumar, M. M. M. Sarcar, et al. · Indian Journal of Engineering and Materials Sciences · 13

Investigation of Dielectric Properties of Industrial Waste Reinforced Particulate Polymer Composites

2014 · Vijaya Kumar Nimmagadda, M. M. M. Sarcar, et al. · Advances in Materials Science and Engineering · 12

PDF

Real-time tool condition monitoring of face milling using acousto-optic emission â an experimental approach

2011 · B. Srinivasa Prasad, M.M.M. Sarcar, et al. · International Journal of Computer Applications in Technology · 12

Studies on cold workability limits of pure copper using machine vision system and its finite element analysis

2008 · J. Appa Rao, J. Babu Rao, et al. · Materials & Design (1980-2015) · 12

Corrosion behavior of duplex coatings

2014 · K. Raghu Ram Mohan Reddy, N. Ramanaiah, et al. · Journal of King Saud University - Engineering Sciences · 11

PDF

Automatic Recognition of Machining Features using STEP Files

2013 · V. Naga Malleswari, P. Madar Valli, et al. · 11

Deformation behavior of Al–4Cu–2Mg alloy during cold upset forging

2008 · J. Babu Rao, Syed Kamaluddin, et al. · Journal of Alloys and Compounds · 11

Experimental investigation to predict the condition of cutting tool by surface texture analysis of images of machined surfaces based on amplitude parameters

2008 · B.S. Prasad, M.M.M. Sarcar · International Journal of Machining and Machinability of Materials · 10

An Experimental Study on the Effect of Weld Parameters on Mechanical and Micro structural Properties of Dissimilar Aluminium Alloy FS Welds

2014 · R. Madhusudhan, M. M. M. Sarcar, et al. · 9

Automated generation of NC part programs for turned parts based on 2-D drawing image files

2011 · S. Srinivasa Rao, B. Satyanarayana, et al. · International Journal of Production Research · 9

Studies on Flow Behavior of Aluminum Using Vision System during Cold Upsetting

2007 · Syed Kamaluddin, J. Babu Rao, et al. · Metallurgical and Materials Transactions B · 8

Works count: 50

Citation count: 680

H-index: 13

I10-index: 22