Get started
Author

Ikhlas Meddour

Predictive modeling and multi-response optimization of technological parameters in turning of Polyoxymethylene polymer (POM C) using RSM and desirability function
2016 · Amel Chabbi, Mohamed Athmane Yallese, et al. · Measurement · 129
Performance of coated and uncoated mixed ceramic tools in hard turning process
2015 · Hamza Bensouilah, Hamdi Aouici, et al. · Measurement · 125
Modeling and multi-objective optimization for minimizing surface roughness, cutting force, and power, and maximizing productivity for tempered stainless steel AISI 420 in turning operations
2018 · Abderrahmen Zerti, Mohamed Athmane Yallese, et al. · The International Journal of Advanced Manufacturing Technology · 114
Investigation and modeling of cutting forces and surface roughness when hard turning of AISI 52100 steel with mixed ceramic tool: cutting conditions optimization
2014 · I. Meddour, M. A. Yallese, et al. · The International Journal of Advanced Manufacturing Technology · 93
Prediction of surface roughness and cutting forces using RSM, ANN, and NSGA-II in finish turning of AISI 4140 hardened steel with mixed ceramic tool
2018 · Ikhlas Meddour, Mohamed Athmane Yallese, et al. · The International Journal of Advanced Manufacturing Technology · 87
Modeling and optimization of turning process parameters during the cutting of polymer (POM C) based on RSM, ANN, and DF methods
2017 · A. Chabbi, M.A. Yallese, et al. · The International Journal of Advanced Manufacturing Technology · 82
Modeling and optimization in dry face milling of X2CrNi18-9 austenitic stainless steel using RMS and desirability approach
2017 · Abdel-Ali Selaimia, Mohamed Athmane Yallese, et al. · Measurement · 73
On the Modeling of Surface Roughness and Cutting Force when Turning of Inconel 718 Using Artificial Neural Network and Response Surface Methodology: Accuracy and Benefit
2017 · Hamid Tebassi, Mohamed Athmane Yallese, et al. · Periodica Polytechnica Mechanical Engineering · 47
Behaviour of lignocellulosic fibre-reinforced cellular core under low-velocity impact loading: Taguchi method
2020 · Moncef Cherief, Ahmed Belaadi, et al. · The International Journal of Advanced Manufacturing Technology · 42
Performance comparison of wiper and conventional ceramic inserts in hard turning of AISI 4140 steel: analysis of machining forces and flank wear
2016 · H. Aouici, M. Elbah, et al. · The International Journal of Advanced Manufacturing Technology · 36
Multi-objective optimization of surface roughness, cutting forces, productivity and Power consumption when turning of Inconel 718
2015 · Hamid Tebassi, Mohamed Athmane Yallese, et al. · International Journal of Industrial Engineering Computations · 28
PDF
Selection of bearing health indicator by GRA for ANFIS-based forecasting of remaining useful life
2021 · Ikhlas Meddour, Salah Eddine Messekher, et al. · Journal of the Brazilian Society of Mechanical Sciences and Engineering · 19
New criteria for wrapper feature selection to enhance bearing fault classification
2023 · Mohammed Amine Sahraoui, Chemseddine Rahmoune, et al. · Advances in Mechanical Engineering · 17
PDF
Host-guest complex of nabumetone: β-cyclodextrin: quantum chemical study and QTAIM analysis
2017 · Nadjia Bensouilah, Baya Boutemeur-Kheddis, et al. · Journal of Inclusion Phenomena and Macrocyclic Chemistry · 16
Development of an adaptive tool condition monitoring system: integration of case-based reasoning with CNN
2025 · Oussama Dahmoune, Ikhlas Meddour, et al. · Journal of Intelligent Manufacturing · 10
Dependability analysis in systems engineering approach using the FMECA extracted from the SysML and failure modes classification by K-means
2021 · Ali Chabane, Smail Adjerid, et al. · International Journal of Dynamics and Control · 10
Self-Organizing Maps and VMD for Accurate Diagnosis of Bearing Defects
2023 · Ismail Nouioua, Ramdane Younes, et al. · Journal of Vibration Engineering & Technologies · 9
Comparison between sound perception and self-organizing maps in the monitoring of the bearing degradation
2020 · Saiefeddine Alia, Rachid Nasri, et al. · The International Journal of Advanced Manufacturing Technology · 8
Comparative assessment between DFA, NSGA-II coupled with TOPSIS, GRA, and TOPSIS for multiobjective optimization of gray cast iron turning process using CBN insert
2023 · Salim Chihaoui, Ikhlas Meddour, et al. · Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering · 7
A new method for evaluation nominal coefficient of friction and frictional forces in turning and inserts characterization using cutting forces profiles
2015 · Hamid Tebassi, Mohamed Athmane Yallese, et al. · Engineering Solid Mechanics · 7
PDF
Enhancing air compressors multi fault classification using new criteria for Harris Hawks optimization algorithm in tandem with MODWPT and LSSVM classifier
2023 · Chemseddine Rahmoune, Mohammed Amine Sahraoui, et al. · Advances in Mechanical Engineering · 6
Investigation and Modeling of Surface Roughness of Hard Turned AISI 52100 Steel: Tool Vibration Consideration
2015 · Ikhlas Meddour, Mohamed Athmane Yallese, et al. · Applied condition monitoring · 5
Factors influencing the effect of attached mass on dynamic behavior of laminate composite plates using Taguchi technique
2018 · Abdelhafid Rahmane, Toufik Benmansour, et al. · Journal of the Brazilian Society of Mechanical Sciences and Engineering · 4
Deep Transfer Learning and Data Augmentation for Automatic Flank Wear Detection and Classification
2025 · Mohamed ELBAH, Oussama DAHMOUNE, et al. · Research Square
PDF
Deep Transfer Learning and Data Augmentation for Automatic Flank Wear Detection and Classification
2025 · Oussama Dahmoune, Mohamed Elbah, et al. · SSRN Electronic Journal
Works count: 27
Citation count: 974
H-index: 14
I10-index: 16
Year
Topic
Type