Get started
Author

Hartmut Hoffmann

Observed names: Hoffmann, Hartmut, Hoffmann, Hartmut 1942-
OpenAlex ID: A5110123966
An investigation of the blanking process of the quenchable boron alloyed steel 22MnB5 before and after hot stamping process
2011 · Hyunwoo So, Dennis Faßmann, et al. · Journal of Materials Processing Technology · 152
Method for optimizing the cooling design of hot stamping tools
2007 · Heinz Steinbeiss, Hyunwoo So, et al. · Production Engineering · 75
Handbuch Umformen
2012 · Hartmut Hoffmann, Reimund Neugebauer, et al. · Carl Hanser Verlag GmbH & Co. KG eBooks · 72
Simulation of wear on sheet metal forming tools—An energy approach
2008 · Kivilcim Ersoy-Nürnberg, Gerald Nürnberg, et al. · Wear · 66
Failure prediction for nonlinear strain paths in sheet metal forming
2012 · Wolfram Volk, Hartmut Hoffmann, et al. · CIRP Annals · 51
In-situ measurement of phase transformation kinetics in austempered ductile iron
2013 · Leopold Meier, Michael Hofmann, et al. · Materials Characterization · 48
Development of a continuous composite casting process for the production of bilayer aluminium strips
2014 · Christoph Nerl, Martin Wimmer, et al. · Journal of Materials Processing Technology · 36
Interaction of heat generation and material behaviour in sheet metal blanking
2015 · Peter Demmel, Hartmut Hoffmann, et al. · CIRP Annals · 33
Reduction of springback using simultaneous stretch-bending processes
2011 · Hansjörg Schilp, Joungsik Suh, et al. · International Journal of Material Forming · 24
On the influence of Seebeck coefficients on adhesive tool wear during sheet metal processing
2017 · Philipp Tröber, Peter Demmel, et al. · CIRP Annals · 19
Experimental investigation of the lateral forces during shear cutting with an open cutting line
2016 · Thomas Kopp, Jens Stahl, et al. · Journal of Materials Processing Technology · 16
Rotary Blanking
1999 · Hartmut Hoffmann, Michael Schweitzer, et al. · CIRP Annals · 16
Influence of non-proportional load paths and change in loading direction on the failure mode of sheet metals
2020 · Wolfram Volk, Roman Norz, et al. · CIRP Annals · 15
Simulation Assisted Analysis of Material Flow in Roller Clinched Joints
2014 · Daniel Rill, Maria Weiß, et al. · Advanced materials research · 14
FEM simulation and experimental research on the AlMg4.5Mn0.4 sheet blanking
2002 · Xu Shuqin, Michael Hoogen, et al. · Journal of Materials Processing Technology · 14
Characterization of the Thermoelectric Behavior of Plastically Deformed Steels by Means of Relative Seebeck Coefficient
2013 · Peter Demmel, Philipp Tröber, et al. · Materials science forum · 13
Clean-sheared and rectangular edges through counter-shaving
2007 · Hartmut Hoffmann, Florian Hörmann · Production Engineering · 13
Manufacturing efficient electrical motors with a predictive maintenance approach
2019 · Hannes Alois Weiss, Nora Leuning, et al. · CIRP Annals · 12
Cutting of hollow profiles using electromagnetic fields
2010 · Paul Maier-Komor, Hartmut Hoffmann, et al. · International Journal of Material Forming · 11
Light Metal in High-Speed Stamping Tools
2011 · Martin Hirsch, Peter Demmel, et al. · Key engineering materials · 9
Automatic Process Control in Press Shops
2007 · Hartmut Hoffmann, Michael F. Zaeh, et al. · Key engineering materials · 9
Methods to Decrease Cut Edge Sensitivity of High Strength Steels
2014 · Thorsten Gläsner, Christina Sunderkötter, et al. · Key engineering materials · 8
In Situ Strain Measurements during Casting Using Neutron Diffraction
2013 · Matthias Reihle, Michael Hofmann, et al. · Materials science forum · 8
Experimental Investigation on the Temperature Distribution in the Shearing Zone During Sheet Metal Blanking
2012 · Peter Demmel, T. Kopp, et al. · mediaTUM – the media and publications repository of the Technical University Munich (Technical University Munich) · 8
Model based strategies for an optimised ribbing design of large forming tools
2009 · Nicholas Drude, Leopold Meier, et al. · Production Engineering · 8
Works count: 102
Citation count: 851
H-index: 14
I10-index: 19
Year
Topic
Type