Get started
Author

P. Bocher

Observed names: Bocher, P., Bocher, Philippe, Philippe Bocher
OpenAlex ID: A5111552728
Flow stress prediction during hot working of near-α titanium alloys
2006 · P. Vo, M. Jahazi, et al. · Materials Science and Engineering A · 105
On the effectiveness of surface severe plastic deformation by shot peening at cryogenic temperature
2016 · M. Novelli, J-J. Fundenberger, et al. · Applied Surface Science · 76
Experimental and numerical investigation of material heterogeneity in shot peened aluminium alloy AA2024-T351
2013 · A. Gariépy, F. Bridier, et al. · Surface and Coatings Technology · 67
Effect of alloying elements on the isothermal solidification during TLP bonding of SS 410 and SS 321 using a BNi-2 interlayer
2007 · M.A. Arafin, M. Medraj, et al. · Materials Chemistry and Physics · 54
Multiphysics Modeling of Induction Hardening of Ring Gears for the Aerospace Industry
2011 · Alessandro Candeo, Christophe Ducassy, et al. · IEEE Transactions on Magnetics · 51
Evaluation of Residual Stresses Induced by Robotized Hammer Peening by the Contour Method
2008 · L. Hacini, N. Van Lê, et al. · Experimental Mechanics · 45
High and low cycle fatigue behavior of linear friction welded Ti–6Al–4V
2014 · J.C. Stinville, F. Bridier, et al. · International Journal of Fatigue · 43
On the effect of the orientation of sheet rolling direction in shot peen forming
2013 · A. Gariépy, S. Larose, et al. · Journal of Materials Processing Technology · 43
Effect of shot peening temperature on the microstructure induced by surface severe plastic deformation on an austenitic stainless steel
2025 · Yann Austernaud, Marc Novelli, et al. · Journal of Materials Processing Technology · 31
Water droplet impact erosion damage initiation in forged Ti–6Al–4V
2014 · N. Kamkar, F. Bridier, et al. · Wear · 30
Distortion and residual stress measurements of induction hardened AISI 4340 discs
2013 · J. Yi, M. Gharghouri, et al. · Materials Chemistry and Physics · 25
Flow stress and recrystallisation during hot deformation of Cu–9%Sn alloys
1999 · B. Bayle, P. Bocher, et al. · Materials Science and Technology · 14
Influence of Hard Turning on Microstructure Evolution in the Subsurface Layers of Inconel 718
2014 · H. Touazine, M. Jahazi, et al. · ASME International Mechanical Engineering Congress and Exposition (IMECE) · 5
Effect of solutes on the dynamic recrystallization microstructure of nickel
2001 · R. Le Gall, P. Bocher, et al. · Journal de Physique IV (Proceedings) · 4
Equivalent Inclusion Method (EIM) for isotropic and anisotropic spatially oriented spheroidal inhomogeneities: A unified calculation module validated via comparisons to Finite Element (FE) simulations
2024 · Rémy Serre, Carole Nadot-Martin, et al. · Mechanics of Materials · 3
PDF
Mechanical Properties of Cast & Wrought Hybrid Disks
2016 · P. Bocher, F. Bridier, et al. · 3
The microstructural modelling of room temperature creep in titanium alloys using a cellular automata model
2008 · N. Boutana, P. Bocher, et al. · International Journal of Microstructure and Materials Properties · 3
Temperature history modeling and validation of fast induction hardening process
2016 · Senhaji, Achraf, Larregain, Benjamin, et al. · HAL
Finite element analysis of serrated chip formation in machining of 7075-T651 alluminum alloy
2016 · Wahbi Jomaa, J. Mechri, et al. · Espace ÉTS (ETS)
Deformation processing mechanism and microstructural evolution in a near-alpha titanium alloy
2005 · P. Wanjara, H. Monajati, et al. · NPARC
Variant Selection in Forged Titanium Alloys: Effect of Microscopic Grain Misorientations on the Formation of Macroscopic Regions with Similar Crystallographic Orientations
2005 · Bocher, P., Jahazi, M., et al. · HAL
Works count: 29
Citation count: 605
H-index: 12
I10-index: 12
Year
Topic
Type