Get started
Author

Rean Der Chien

Observed names: R.-D. Chien, R.D. Chien, Rean der Chien, Rean-Der Chien
OpenAlex ID: A5111759222
Analyses and measurements on bending performance of gas-assisted injection molded parts
1999 · Shia-Chung Chen, Sheng-Yan Hu, et al. · Advances in Polymer Technology · 54
Preliminary study of polymer melt rheological behavior flowing through micro-channels
2005 · S.C. Chen, R.I. Tsai, et al. · International Communications in Heat and Mass Transfer · 50
Study on the Molding Characteristics and Mechanical Properties of Injection-molded Foaming Polypropylene Parts
2004 · Rean Der Chien, Shia-Chung Chen, et al. · Journal of Reinforced Plastics and Composites · 48
Optimization of the injection molding process for short-fiber-reinforced composites
2011 · Ch.-Sh. Chen, T.-J. Chen, et al. · Mechanics of Composite Materials · 29
Investigation of gas‐assisted injection molding. Part III: Effect of gas channel design on part bending strength
1998 · Shia‐Chung Chen, Sheng‐Yan Hu, et al. · Polymer Engineering and Science · 19
Investigations on the Weldline Tensile Strength of Thin-wall Injection Molded Parts
2004 · Rean Der Chien, Shia-Chung Chen, et al. · Journal of Reinforced Plastics and Composites · 15
Investigations into moulding window of gas assisted injection moulded polystyrene plates with various gas channel designs
2002 · Rean Der Chien, Shia-Chung Chen, et al. · Plastics Rubber and Composites Macromolecular Engineering · 15
Effect of Gas Channel Design on Bending Properties of Gas-Assisted Injection Molded Polystyrene Parts
1998 · Rean Der Chien, Shia-Chung Chen, et al. · Journal of Reinforced Plastics and Composites · 15
Integrated simulations of structural performance, molding process, and warpage for gas-assisted injection-molded parts. I. Analysis of part structural performance
1998 · Shia-Chung Chen, Sheng-Yan Hu, et al. · Journal of Applied Polymer Science · 14
Response of a sequential‐valve‐gate system used for thin‐wall injection molding
2005 · Shia‐Chung Chen, Rean Der Chien, et al. · Journal of Applied Polymer Science · 10
Hot embossing of micro-featured devices
2005 · S.C. Chen, M.C. Lin, et al. · IEEE International Conference on Mechatronics (ICM) · 8
Effect of moulding conditions on the tensile strength of cyclic olefin copolymers (COC) injection moulded parts
2005 · R.-D. Chien, C.-S. Chen, et al. · Plastics Rubber and Composites Macromolecular Engineering · 8
Investigations on the Impact Performance of Gas-Assisted Injection Molded Polystyrene Parts
1999 · Rean der Chien, Ching-Kuo Cheng, et al. · Journal of Reinforced Plastics and Composites · 8
Effects of Process Parameters on Replication Accuracy of Microinjection Molded Cyclic Olefins Copolymers Parts
2013 · Hsuan-Liang Lin, Chun-Sheng Chen, et al. · Japanese Journal of Applied Physics · 6
PDF
Effect of gas channel design on the molding window of gas‐assisted‐injection‐molded polystyrene parts
2003 · Rean Der Chien, Shia‐Chung Chen, et al. · Journal of Applied Polymer Science · 5
Surface Visual Quality of Gas-Assisted Injection Molded ABS Parts with Various Gas Channel Designs
2004 · Shia-Chung Chen, Ming-Chung Lin, et al. · Journal of Reinforced Plastics and Composites · 4
Study of the Bending Properties in Gas-assisted Injection Molded Fiber-reinforced Nylon Parts
2004 · Rean Der Chien, Nien-Tien Cheng, et al. · Journal of Reinforced Plastics and Composites · 3
Study of mouldability in gas-assisted injection moulded fibre-reinforced Nylon parts
2004 · S.-C. Chen, R.D. Chien, et al. · Plastics Rubber and Composites Macromolecular Engineering · 3
Investigations into surface visual quality of gas-assisted injection moulded polypropylene parts
2004 · Rean Der Chien, Shia-Chung Chen · Plastics Rubber and Composites Macromolecular Engineering · 2
Works count: 19
Citation count: 316
H-index: 10
I10-index: 10
Year
Topic
Type