Author

Naeem Ullah Dar

Observed names: N DAR, N U Dar, N. U. Dar, N.U. Dar, Naeem U. Dar, Nameem Ullah Dar

Institution: University of Engineering and Technology Taxila

Observed institutions: University of Engineering and Technology Taxila, National University of Sciences and Technology

OpenAlex ID: A5111862129

Tool and lubrication for negative incremental forming of a commercially pure titanium sheet

2007 · G. Hussain, L. Gao, et al. · Journal of Materials Processing Technology · 129

A fuzzy expert system for optimizing parameters and predicting performance measures in hard-milling process

2006 · A IQBAL, N HE, et al. · Expert Systems with Applications · 103

An experimental study on some formability evaluation methods in negative incremental forming

2007 · G. Hussain, L. Gao, et al. · Journal of Materials Processing Technology · 82

Analysis of circumferentially arc welded thin-walled cylinders to investigate the residual stress fields

2008 · Afzaal M. Malik, Ejaz M. Qureshi, et al. · Thin-Walled Structures · 80

The formability of annealed and pre-aged AA-2024 sheets in single-point incremental forming

2009 · G. Hussain, L. Gao, et al. · The International Journal of Advanced Manufacturing Technology · 69

Modeling the effects of cutting parameters in MQL-employed finish hard-milling process using D-optimal method

2007 · Asif Iqbal, He Ning, et al. · Journal of Materials Processing Technology · 61

Analysis of weld-induced residual stresses and distortions in thin-walled cylinders

2009 · Naeem Ullah Dar, Ejaz M. Qureshi, et al. · Journal of Mechanical Science and Technology · 43

A comparative study on the forming limits of an aluminum sheet-metal in negative incremental forming

2007 · G. Hussain, N.U. Dar, et al. · Journal of Materials Processing Technology · 39

Optimizing cutting parameters in minimum quantity of lubrication milling of hardened cold work tool steel

2008 · A Iqbal, N U Dar, et al. · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · 28

Comparison of fuzzy expert system based strategies of offline and online estimation of flank wear in hard milling process

2006 · Asif Iqbal, Ning He, et al. · Expert Systems with Applications · 22

Comprehensive Mechanical Behavior of Thin-Walled Additively-Manufactured Parts of AlSi10Mg by SLM in As-Built, Post-Solution, and Aging Treatment Conditions

2023 · Arfan Majeed, Muhammad Muzamil, et al. · JOM · 13

Self-developing fuzzy expert system: a novel learning approach, fitting for manufacturing domain

2009 · Asif Iqbal, Naeem U. Dar, et al. · Journal of Intelligent Manufacturing · 12

Residual Stress Fields due to Varying Tack Welds Orientation in Circumferentially Welded Thin-Walled Cylinders

2009 · E. M. Qureshi, A. M. Malik, et al. · Advances in Mechanical Engineering · 12

An Investigation into the Fatigue Crack Growth Rate of Electron Beam-Welded H13 Tool Steel: Effect of Welding and Post-Weld Heat Treatment

2014 · Masood Shah, Mifrah Ali, et al. · Metallography Microstructure and Analysis · 9

Numerical simulation and experimental verification of CMOD in SENT specimen: Application on FCGR of welded tool steel

2013 · Amir Sultan, Riffat Asim Pasha, et al. · Acta Metallurgica Sinica (English Letters) · 9

Optimal formation of fuzzy rule-base for predicting process’s performance measures

2010 · Asif Iqbal, Naeem Ullah Dar · Expert Systems with Applications · 7

Adaptive sliding-mode hybrid force/position controller for flexible joint robot

2008 · M. Farooq, Dao Bo Wang, et al. · IEEE International Conference on Mechatronics and Automation (ICMA) · 7

Analysis of circumferentially welded thin-walled cylinders to investigate the effects of varying clamping conditions

2008 · A M Malik, Ejaz M Qureshi, et al. · Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture · 6

Analysis of circumferentially welded thin-walled cylinders to study the effects of tack weld orientations and joint root opening on residual stress fields

2009 · N U Dar, E M Qureshi, et al. · Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science · 5

Expert System For Optimization Of Welding Process Of Thin Walled HSLA Steel Structures

2009 · Naeem Ullah Dar · HEC National Digital Library · 5

New Methodologies for the Determination of Precise Forming Limit Curve in Single Point Incremental Forming Process

2010 · Ghulam Hussain, Gao Lin, et al. · Advanced materials research · 4

A Reconfigurable and Modular Open Architecture Controller: The New Frontiers

2008 · Muhammad Farooq, Dao Bo Wang, et al. · Lecture notes in electrical engineering · 3

A Fundamental Investigation on the Formability of a Commercially-Pure Titanium Sheet-Metal in the Incremental Forming and Stamping Processes

2007 · G. Hussain, L. Gao, et al. · ASME International Manufacturing Science and Engineering Conference (MSEC) · 3

A Self Progressing Fuzzy Rule-Based System for Optimizing and Predicting Machining Process

2009 · Asif Iqbal, Naeem U. Dar · Lecture notes in electrical engineering · 2

Analysis of Arc Welded Thin-Walled Cylinders to Investigate the Effects of Welding Process Parameters on Residual Stresses

2008 · Afzaal M. Malik, Ejaz M. Qureshi, et al. · Materials science forum · 1

Works count: 31

Citation count: 756

H-index: 12

I10-index: 13